PRODUCTION LOT TESTING

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 29 PAGES SPE4A6-23-T-621B SECTION A cancelling of requirements assumed to be non-procurable due to no quotes/sources. The submission of an anticipated quote date does not preclude DLA from making an award to another acceptable timely offer. DLA funds Procurement Technical Assistance Centers (PTACs) to increase the number of U.S. businesses capable of bidding and performing on local, state, and federal government contracts. PTACs have government contracting experts available to assist suppliers at no cost. Visit our website to find your local PTAC: http://www.dla.mil/HQ/SmallBusiness/PTAP.aspx THE OFFEROR, BY SUBMISSION OF ITS QUOTATION, REPRESENTS IT WILL NOT PROVIDE COVERED TELECOMMUNICATIONS EQUIPMENT OR SERVICES TO THE GOVERNMENT IN THE PERFORMANCE OF ANY AWARD RESULTING FROM THIS SOLICITATION, IN

ACCORDANCE WITH PARAGRAPH (d)OF THE CLAUSE AT FAR 52.204-24, REPRESENTATION REGARDING CERTAIN TELECOMMUNICATIONS AND VIDEO SURVEILLANCE SERVICES OR EQUIPMENT, OR IN ACCORDANCE WITH ITS EXISTING REPRESENTATION IN PARAGRAPH (c) OF THE PROVISION AT DFARS 252.204-7016, COVERED DEFENSE TELECOMMUNICATIONS EQUIPMENT OR SERVICES – REPRESENTATION. Caution Notice: Offerors are required to comply with domestic material restrictions. The Berry Amendment, the Buy American Act, and other domestic material restriction may apply. Offerors are instructed to refer to the solicitation clauses related to foreign sourcing for more information on applicability. The Berry Amendment threshold has been reduced to $150,000 and vendors must carefully review related clauses DFARS 252.225-7006, 252.225-7012, and 252.225-7015 for applicability requirements. If your offer is based on a non-domestic material, you are required to provide disclosure information in your quote and/or through written notification to the point of contact listed in the solicitation. DoD Class Deviation 2023-O0001: A small business joint venture offeror must submit, with its offer, the representation required in paragraph (c) of FAR solicitation provision 52.212-3, Offeror Representations and CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 29 PAGES SPE4A6-23-T-621B SECTION A Certifications-Commercial Products and Commercial Services, and paragraph (c) of FAR solicitation provision 52.219-1, Small Business Program Representations, in accordance with 52.204-8(d) and 52.212- 3(b) for the following categories: (A) Small business; (B) Service-disabled veteran-owned small business; (C) Women-owned small business (WOSB) under the WOSB Program; (D) Economically disadvantaged women-owned small business under the WOSB Program; or (E) Historically underutilized business zone small business. Contractors shall not provide parts and supplies made using additive manufacturing (AM), unless AM is specifically authorized in the solicitation/contract. See procurement note L31. Procurement History for NSN/FSC:011474595/1560 CAGE Contract Number Quantity Unit Cost AWD Date Surplus Material . 26512 F0960383G1713SM0900 1.000 275.79000 19840828 N This solicitation is being issued under the First Destination Transportation (FDT) program to reduce cost of transportation through the use of Government-Arranged Transportation utilizing Government contracts and rates. Offers should be submitted based on FOB Origin. For offerors whose shipments will orginate from outside the contiguous United States, the offeror's FOB Origin price shall include transportation to a contiguous United States location that the offeror selects based on cost effectiveness or other variables at the offeror's discretion. Additional information about FDT can be found at: http://www.dla.mil/FDTPI/ CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 29 PAGES SPE4A6-23-T-621B SECTION B PR: 7001148628 NSN/MATERIAL:1560011474595 ITEM DESCRIPTION RIB,AIRFOIL RIB,AIRFOIL RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RD002, COVERED DEFENSE INFORMATION APPLIES RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS) RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER) RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies. RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 29 PAGES SPE4A6-23-T-621B SECTION B (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. IUID REQUIRED: This item requires Item Unique Identification (IUID) in accordance with the enclosed/referenced IUID technical requirements and MIL-STD-130. DFARS 252.211-7003 clause applies. RT001: MEASURING AND TEST EQUIPMENT MIL-STD-130N(1) DATED 16 NOV 2012. IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. ENGINEERING DATA REQUIREMENTS: 1.THE ENGINEERING NOTES ARE UNDER DRAWING:7604845-201308306 IN DMS THE FOLLOWING NOTES APPLY:2-6, 11 AND 28. 2.WHEN MILITARY DOCUMENTS LISTED IN THE ENGINEERING DRAWING ARE CANCELLED THEY SHALL BE REPLACED BY THE INDUSTRY EQUIVALENT DOCUMENT SPECIFIED ON THE MILITARY DOCUMENT'S CANCELLATION NOTICE. THE CHARACTERISTICS OF TYPE, GRADE, CLASS, ETC. SPECIFIED IN THE CANCELLED MILITARY DOCUMENT SHALL BE MAINTAINED OR EXCEED THOSE CHARACTERISTICS WHEN APPLYING THE INDUSTRY EQUIVALENT DOCUMENT(S). THE CONTRACTOR WILL COORDINATE WITH THE PROPER A-10 ENGINEERING ORGANIZATION FOR AUTHORIZATION AND APPROVAL OF THESE SUBSTITUTIONS PRIOR TO THE MANUFACTURING OF THIS COMPONENT. WHEN THERE IS NO LISTED REPLACEMENT THE CONTRACTOR SHALL REQUEST AND RECOMMEND A SUBSTITUTE DOCUMENT FROM THE PROPER A-10 ENGINEERING ORGANIZATION BY CONTACTING THE GOVERNMENT CONTRACTING OFFICIAL. 3.USE OF NORTHROP GRUMMAN SPECIFICATION Z-R701 IN CONJUNCTION WITH MIL-STD-130 IS MANDATORY TO ENSURE THE PROPER MARKING OF THE PARTS. (Z-R701 HAS UNLIMITED DATA RIGHTS IN JEDMICS) 4."IUID" (ITEM UNIQUE IDENTIFIER) IS REQUIRED IAW MIL-STD-130. SPECIFIC CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 29 PAGES SPE4A6-23-T-621B SECTION B INSTRUCTIONS FOR MARKING METHODS, LOCATION, CONTENT AND FORMAT SHALL BE SPECIFIED BY THE CONTRACTOR AND SUBMITTED TO THE GOVERNMENT FOR APPROVAL PRIOR TO CONTRACT DELIVERY. THE CONTRACTOR MUST DEMONSTRATE THE MARKING DOES NOT ADVERSELY AFFECT ITEM INTEGRITY OR PERFORMANCE AND WILL REMAIN READABLE AND ATTACHED THROUGHOUT THE USEABLE LIFE OF THE ITEM. IUID IS REQUIRED FOR ITEMS WHERE THE INDIVIDUAL COST PER UNIT IS GREATER THAN $5 ,000 OR IF THE ITEM HAS BEEN IDENTIFIED AS FATIGUE CRITICAL REGARDLESS OF THE ITEMS PER UNIT COST. 5.USE OF ANY PROCESS OR MANUFACTURING TECHNIQUE WHICH CREATES A NET EDGE ON A METALLIC PART BY RELYING ON HEAT AT OR ABOVE THE PARTS MELTING POINT TO PRODUCE THE CUT IS NOT GENERALLY AUTHORIZED (I.E. LASER CUTTING, ELECTRICAL DISCHARGE MACHINE (EDM), PLASMA CUTTING, ETC.) WITHOUT PRIOR A-10 SYSTEM PROGRAM OFFICE APPROVAL. LIKEWISE, OTHER NON-HEAT GENERATING CUTTING PROCESSES INVOLVING HIGH PRESSURE FLUIDS AND SLURRIES (I.E., WATER JET) ARE ALSO NOT CURRENTLY APPROVED FOR USE IN THE PRODUCTION OF A-10 PARTS. ONLY THOSE PROCESSES CONTROLLED BY A-10 APPROVED PROGRAM SPECIFICATIONS AND A-10 DRAWINGS ARE PERMITTED TO BE USED IN THE MANUFACTURE OF A-10 PARTS AND ASSEMBLIES. 6.DRAWING:Z-R701 MARKINGS & IDENTIFICATION REQUIREMENTS WITH AT-1. GOVERNMENT FIRST ARTICLE TESTING REQUIREMENTS: Government First Article Preproduction approval required. Testing will be in accordance with applicable drawings, specifications and/or Engineering instructions. The first article offered shall be manufactured at the facilities in which production quantities are procured and produced under this contract. When submitting the first article(s) for government testing, a copy of the contract and all applicable drawings, specifications, engineering instructions, certifications, and inspection sheets shall be provided. Upon receipt and evaluation of the test report from the responsible government testing location, the contracting officer will provide final notification to the manufacturer. Any questions or concerns regarding the first article test requirements must be submitted through the contracting officer. Additional Wide Area Workflow (WAWF) instructions for government first article test CLIN: The contractor shall code the receiving report for government first article test CLIN in WAWF as Follows: A: Inspection at origin (Source) - Enter the DCMA office DODAAC listed on page 1 of the contract. B: Acceptance by other - Enter the issue by office DODAAC listed on page 1 of the contract. C: Ship to code - Enter the DODAAC of the test facility listed for the CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 10 OF 29 PAGES SPE4A6-23-T-621B SECTION B government first article test CLIN in the contract (See FAR Clause 52.209-4). FIRST ARTICLE TEST MARKING INSTRUCTIONS: FAT sample(s) packaging shall be clearly marked "FIRST ARTICLE TEST EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contrasting color to the packaging. Marking shall be located adjacent to the Package Shipping Label side and on at least one additional side of the package. A.PERFORMANCE OR OTHER CHARACTERISTICS WHICH THE FIRST ARTICLES MUST MEET ARE CONFORMANCE WITH ALL DRAWINGS, 3D MODELS, SPECIFICATIONS, FORM, FIT, AND FUNCTION. B. THE DETAILED TECHNICAL REQUIREMENTS FOR FIRST ARTICLE APPROVAL TESTS ARE CONTAINED IN THE GOVERNMENT RESERVES THE RIGHT TO TEST ITEM TO ANY SPECIFICATION INCLUDED IN THE CONTRACT. FIRST ARTICLE DELIVERY ADDRESS: DODAAC:FB2029 MARK AS "FIRST ARTICLE. DO NOT SEND TO SUPPLY. OO-ALC/809 MXSS/MXDEB BLDG 849 ATTN: NON-ACCOUNTABLE BAY HILL AIR FORCE BASE, UT 84056-5713 PLEASE ENSURE THE WORDS 'FIRST ARTICLE' ARE MARKED ON THE OUTSIDE OF THE BOX IN LARGE CONSPICUOUS LETTERS. CRITICAL APPLICATION ITEM IAW BASIC DRAWING NR 77751 160D514104 REVISION NR T DTD 09/22/2016 PART PIECE NUMBER: 160D514104-14 IAW REFERENCE DRAWING NR 77751 B-F501 REVISION NR D DTD 10/24/2017 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 77751 SP664 REVISION NR M DTD 11/27/1978 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 77751 G-F101 REVISION NR C DTD 09/10/2014 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 77751 Z-R701 REVISION NR C DTD 02/10/1998 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 77751 SP664 REVISION NR M DTD 04/16/1981 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 77751 Z-R901 REVISION NR F DTD 08/29/2011 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 77751 Z-R701 REVISION NR C1 DTD 02/10/1998 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 77751 Z-R701 REVISION NR C DTD 02/28/1975 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 77751 G-F101 CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 11 OF 29 PAGES SPE4A6-23-T-621B SECTION B REVISION NR C DTD 01/28/2010 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98747 201308306 REVISION NR DTD 05/08/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 77751 160D514104 REVISION NR T DTD 09/22/2016 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 77751 160D514104-14 REVISION NR T DTD 01/01/1939 PART PIECE NUMBER: CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0001 7001148628 0001 EA 77.000 NSN/MATERIAL:1560011474595 DELIVERY (IN DAYS):0305 DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN PREP FOR DELIVERY: PKGING DATA-QUP:001 IF MATERIAL IS CONSIDERED HAZARDOUS IAW FED-STD-313, PACKAGE IN ACCORDANCE WITH TQ REQUIREMENT IP025. IF THE MATERIAL IS NOT CONSIDERED HAZARDOUS, IN ACCORDANCE WITH FED-STD-313, THE MATERIAL SHALL BE COMMERCIALLY PACKAGED IN ACCORDANCE WITH ASTM D3951. All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT PARCEL POST ADDRESS: W25G1U W1A8 DLA DISTRIBUTION DDSP NEW CUMBERLAND FACILITY 2001 NORMANDY DRIVE DOOR 113 TO 134 NEW CUMBERLAND PA 17070-5002 US FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND CONTRACT FREIGHT SHIPPING ADDRESS: W25G1U