CONTRACTOR FIRST ARTIC

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 30 PAGES SPE4A6-24-T-36F1 SECTION A PROVIDE COVERED TELECOMMUNICATIONS EQUIPMENT OR SERVICES TO THE GOVERNMENT IN THE PERFORMANCE OF ANY AWARD RESULTING FROM THIS SOLICITATION, IN ACCORDANCE WITH PARAGRAPH (d) OF THE CLAUSE AT FAR 52.204-24, REPRESENTATION REGARDING CERTAIN TELECOMMUNICATIONS AND VIDEO SURVEILLANCE SERVICES OR EQUIPMENT, OR IN ACCORDANCE WITH ITS EXISTING REPRESENTATION IN PARAGRAPH (c) OF THE PROVISION AT DFARS 252.204-7016, COVERED DEFENSE TELECOMMUNICATIONS EQUIPMENT OR SERVICES – REPRESENTATION. Caution Notice: Offerors are required to comply with domestic material restrictions. The Berry Amendment, the Buy American Act, and other domestic material restrictions may apply. Offerors are instructed to refer to the solicitation clauses related to foreign sourcing for more information on applicability. The Berry Amendment threshold has been reduced to $150,000 and vendors

must carefully review related clauses DFARS 252.225-7006, 252.225-7012, and 252.225-7015 for applicability requirements. If your offer is based on a non-domestic material, you are required to provide disclosure information in your quote and/or through written notification to the point of contact listed in the solicitation. DoD Class Deviation 2023-O0001: A small business joint venture offeror must submit, with its offer, the representation required in paragraph (c) of FAR solicitation provision 52.212-3, Offeror Representations and Certifications-Commercial Products and Commercial Services, and paragraph (c) of FAR solicitation provision 52.219-1, Small Business Program Representations, in accordance with 52.204-8(d) and 52.212- 3(b) for the following categories: (A) Small business; (B) Service-disabled veteran-owned small business; (C) Women-owned small business (WOSB) under the WOSB Program; (D) Economically disadvantaged women-owned small business under the WOSB Program; or (E) Historically underutilized business zone small business. CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 30 PAGES SPE4A6-24-T-36F1 SECTION A Contractors shall not provide parts and supplies made using additive manufacturing (AM), unless AM is specifically authorized in the solicitation/contract. See procurement note L31. Expedited delivery is encouraged for this item. In the instance that an automated evaluation is not used for this solicitation, Contracting Officers may consider an evaluation preference for quotes/offers of fewer delivery days than the number of delivery days requested by the Government. Therefore, suppliers are encouraged to submit their best possible delivery schedule. Procurement History for NSN/FSC:014130853/6150 CAGE Contract Number Quantity Unit Cost AWD Date Surplus Material . 7BUL6 SPE4A622F252LP00003 125.000 1326.00000 20220714 N 7BUL6 SPE4A622PC346P00001 118.000 1450.39000 20220214 N 7BUL6 SPE4A622F6202P00002 125.000 1326.00000 20220104 N 3WGD1 SPE4A621PP766 40.000 1469.86000 20210715 N 3F7B1 SPE4A621PJ226P00003 102.000 1439.85000 20210528 N 3F7B1 SPE4A620PL692P00001 80.000 1439.85000 20200709 N 6V4L8 SPE4A620PJ057P00002 97.000 1342.00000 20200522 N 3WGD1 SPE4A619PM378 112.000 1460.53000 20190823 N 3WGD1 SPE4A619PF053 52.000 1473.30000 20190506 N 3WGD1 SPE4A619C0004 355.000 1448.87000 20181004 N 3WGD1 SPE4A618PN814P00003 115.000 1463.82000 20180823 N 3WGD1 SPE4A618P7173 51.000 1439.21000 20180131 N 3F7B1 SPE4A618P4279P00008 72.000 1629.02000 20171206 N 3F7B1 SPE4A517P6373P00005 57.000 1674.75000 20170505 N 5H723 SPE4A617P9549P00001 104.000 528.43000 20170316 N 3B8L1 SPM4A609D00010003 112.000 563.39000 20100311 N 3B8L1 SPM4A609D0001000204 449.000 547.09000 20081219 N 3B8L1 SPM4A609D00010001 449.000 547.09000 20081022 N 3B8L1 SPM4A608C0223P00003 5400.000 516.86500 20080904 N 3H8V8 SPM4A607C0088P00001 515.000 729.00000 20070703 N This solicitation is being issued under the First Destination Transportation (FDT) program to reduce cost of transportation through the use of Government-Arranged Transportation utilizing Government contracts and rates. Offers should be submitted based on FOB Origin. For offerors whose shipments will orginate from outside the contiguous United States, the offeror's FOB Origin price shall include transportation to a contiguous United States location that the offeror selects based on cost effectiveness or other variables at the offeror's discretion. Additional information about FDT can be found at: http://www.dla.mil/FDTPI/ CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 30 PAGES SPE4A6-24-T-36F1 SECTION B PR: 7006942908 NSN/MATERIAL:6150014130853 ITEM DESCRIPTION CABLE ASSEMBLY,POWER,ELECTRICAL,BRANCHE CABLE ASSEMBLY, POWER,ELECTRICAL RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. RD002, COVERED DEFENSE INFORMATION APPLIES RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS) RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES SAMPLING: CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 30 PAGES SPE4A6-24-T-36F1 SECTION B THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. NOTE: USE CONNECTOR MS27143-1 ILO MS27144-1 (ITEM A ON PL) FOR CIRCUIT 290/291/537 OF THE TRANSMISSION CONTROL MODULE (TCM), ZONE B17 ON DWG 12460097. MIL-STD-130N(1) DATED 16 NOV 2012. IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY Contractor first article/preproduction approval testing required. Use DI-NDTI-80809B in preparation of the first article report. Current revision of MIL-HDBK-831 may also be used for report format guidance. First article testing shall be conducted IAW applicable drawings and drawing notes, specification, engineering instructions and specific requirements set forth in the contract. Additionally, 100% dimensional characteristics check shall be performed and results provided to the contracting officer. The first article offered must be manufactured at the facilities in which production quantities are procured under the contract. Contractor shall provide a statement along with objective evidence that test and production items meet the material and process requirements of the contract. If applicable, DD form 1423 documentation shall be provided as required. Unless F.A.T sample(s) is degraded or destroyed in testing or submitted for government fit, form, function verification (when specified by contract), the F.A.T. samples(s) may be deliverable with the last production run of the contract. Additional Wide Area Workkflow (WAWF) instructions for contractor first article test CLIN: The contractor shall code the receiving report for contractor first article test CLIN in WAWF as follows: A. Inspection at origin (source)- Enter the DCMA DODAAC listed on page 1 of the contract. B. Acceptance at destination- Enter the issue by office DODAAC listed C. Ship to code - Enter the issue by office DODAAC listed on page 1 of the contract. CRITICAL APPLICATION ITEM IAW BASIC DRAWING NR 19207 12460097 REVISION NR J DTD 10/02/2008 PART PIECE NUMBER: 12460097 IAW REFERENCE DRAWING NR 19207 12447170 REVISION NR A DTD 05/09/1996 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12258939 REVISION NR E DTD 10/01/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12259040 REVISION NR D DTD 09/20/2019 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12432476 REVISION NR DTD 11/10/1993 PART PIECE NUMBER: CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 30 PAGES SPE4A6-24-T-36F1 SECTION B IAW REFERENCE DRAWING NR 19207 12340362 REVISION NR D DTD 01/26/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12340512 REVISION NR A DTD 06/14/1996 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12432477 REVISION NR DTD 11/10/1993 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80064 2589945 REVISION NR C DTD 08/10/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7723307 REVISION NR N DTD 12/23/1991 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 8344324 REVISION NR D DTD 02/18/1993 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 8344527 REVISION NR G DTD 10/16/1992 PART PIECE NUMBER: IAW REFERENCE QAP 19207 7722353 REVISION NR D DTD 12/22/1972 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7723474 REVISION NR C DTD 09/30/1997 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 8701325 REVISION NR J DTD 05/16/2012 PART PIECE NUMBER: IAW REFERENCE QAP 19207 8724237 REVISION NR D DTD 05/23/1975 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 7723307 REVISION NR N DTD 12/23/1991 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 8338561 REVISION NR N DTD 09/01/2011 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 8344537 REVISION NR J DTD 09/30/1997 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12339351 REVISION NR E DTD 01/26/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7716520 REVISION NR U DTD 04/04/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7716658 REVISION NR G DTD 02/12/1999 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7722322 CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 10 OF 30 PAGES SPE4A6-24-T-36F1 SECTION B REVISION NR K DTD 11/30/1999 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7982736 REVISION NR R DTD 12/21/2017 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7982907 REVISION NR H DTD 11/03/2015 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 8338566 REVISION NR N DTD 09/01/2011 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 8701309 REVISION NR F DTD 11/14/2018 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 8701329 REVISION NR D DTD 01/22/1999 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 8724237THRU8724250 REVISION NR G DTD 01/04/1999 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7722344 REVISION NR J DTD 01/01/1999 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 10911317 REVISION NR H DTD 09/30/1997 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7716634 REVISION NR L DTD 05/18/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7716684 REVISION NR D DTD 09/30/1997 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 8724253THRU8724262 REVISION NR F DTD 11/03/2015 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7723475 REVISION NR D DTD 10/12/1996 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12447169 REVISION NR B DTD 10/25/2000 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12460126 REVISION NR A DTD 07/30/1996 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12460128 REVISION NR C DTD 05/02/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12460130 REVISION NR B DTD 03/14/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12460131 REVISION NR A DTD 08/01/1996 PART PIECE NUMBER: CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 11 OF 30 PAGES SPE4A6-24-T-36F1 SECTION B IAW REFERENCE DRAWING NR 19207 12460133 REVISION NR B DTD 11/05/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 11668585 REVISION NR B DTD 12/20/1989 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 11668586 REVISION NR A DTD 12/20/1989 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 11668587 REVISION NR B DTD 12/20/1989 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 11668589 REVISION NR B DTD 05/02/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 11668591 REVISION NR B DTD 12/20/1989 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7716780THRU7716785 REVISION NR G DTD 01/22/1999 PART PIECE NUMBER: IAW REFERENCE QAP 19207 7716780 REVISION NR D DTD 12/22/1972 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7722333 REVISION NR C DTD 10/11/1996 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7723308 REVISION NR L DTD 03/24/2004 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 7723309 REVISION NR K DTD 06/04/1992 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7723494 REVISION NR F DTD 09/30/1997 PART PIECE NUMBER: IAW REFERENCE QAP 19207 8724258 REVISION NR E DTD 12/29/1972 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 8724206 REVISION NR T DTD 04/04/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7716521 REVISION NR V DTD 04/04/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12258940 REVISION NR J DTD 02/07/2019 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 11668590 REVISION NR B DTD 04/17/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12460097