PRODUCTION LOT TESTING

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 27 PAGES SPE4A6-24-T-47P8 SECTION A APEX Accelerators, formally known as the Procurement Technical Assistance Program (PTAP), is designed to increase the number of U.S. businesses capable of bidding and performing on local, state, and federal government contracts. APEX Accelerators provide critical assistance to new and existing businesses interested government contracting to enhance the defense industrial base at no cost. Visit https://www.apexaccelerators.us/#/ for more information. 6, THE OFFEROR, BY SUBMISSION OF ITS QUOTATION, REPRESENTS IT WILL NOT PROVIDE COVERED TELECOMMUNICATIONS EQUIPMENT OR SERVICES TO THE GOVERNMENT IN THE PERFORMANCE OF ANY AWARD RESULTING FROM THIS SOLICITATION, IN ACCORDANCE WITH PARAGRAPH (d) OF THE CLAUSE AT FAR 52.204-24, REPRESENTATION REGARDING CERTAIN TELECOMMUNICATIONS AND

VIDEO SURVEILLANCE SERVICES OR EQUIPMENT, OR IN ACCORDANCE WITH ITS EXISTING REPRESENTATION IN PARAGRAPH (c) OF THE PROVISION AT DFARS 252.204-7016, COVERED DEFENSE TELECOMMUNICATIONS EQUIPMENT OR SERVICES – REPRESENTATION. Caution Notice: Offerors are required to comply with domestic material restrictions. The Berry Amendment, the Buy American Act, and other domestic material restrictions may apply. Offerors are instructed to refer to the solicitation clauses related to foreign sourcing for more information on applicability. The Berry Amendment threshold has been reduced to $150,000 and vendors must carefully review related clauses DFARS 252.225-7006, 252.225-7012, and 252.225-7015 for applicability requirements. If your offer is based on a non-domestic material, you are required to provide disclosure information in your quote and/or through written notification to the point of contact listed in the solicitation. DoD Class Deviation 2023-O0001: A small business joint venture offeror must submit, with its offer, the representation required in paragraph (c) of FAR solicitation provision 52.212-3, Offeror Representations and Certifications-Commercial Products and Commercial Services, and paragraph (c) of FAR solicitation provision 52.219-1, Small Business CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 27 PAGES SPE4A6-24-T-47P8 SECTION A Program Representations, in accordance with 52.204-8(d) and 52.212- 3(b) for the following categories: (A) Small business; (B) Service-disabled veteran-owned small business; (C) Women-owned small business (WOSB) under the WOSB Program; (D) Economically disadvantaged women-owned small business under the WOSB Program; or (E) Historically underutilized business zone small business. Contractors shall not provide parts and supplies made using additive manufacturing (AM), unless AM is specifically authorized in the solicitation/contract. See procurement note L31. Procurement History for NSN/FSC:016298432/5305 CAGE Contract Number Quantity Unit Cost AWD Date Surplus Material . 083L8 SPE4A524F2985 10.000 1.19000 20231129 N 083L8 SPE4A523F8421 36.000 1.19000 20230516 N 083L8 SPE4A622F301C 4.000 1.08000 20220810 N 083L8 SPE4A622F300G 4.000 1.08000 20220809 N 083L8 SPE4A622F300F 4.000 1.08000 20220809 N 083L8 SPE4A622F238M 20.000 1.08000 20220705 N 083L8 SPE4A622F233C 20.000 1.08000 20220629 N 083L8 SPE4A622F103Q 25.000 1.08000 20220512 N 083L8 SPE4A622F083U 4.000 1.08000 20220425 N 083L8 SPE4A622F2195 25.000 0.98000 20211024 N 083L8 SPE4A622F2107 6.000 0.98000 20211021 N 083L8 SPE4A622F2105 6.000 0.98000 20211020 N 083L8 SPE4A621F503X 24.000 0.98000 20210923 N 083L8 SPE4A621F485J 20.000 0.98000 20210920 N 083L8 SPE4A621F484F 288.000 0.98000 20210917 N 083L8 SPE4A621F102B 18.000 0.98000 20210427 N 083L8 SPE4A621F097W 32.000 0.98000 20210426 N 083L8 SPE4A621F7999P00001 3.000 0.95000 20210212 N 083L8 SPE4A621F7199P00001 32.000 0.95000 20210204 N 083L8 SPE4A621F1713P00001 18.000 0.95000 20201027 N This solicitation is being issued under the First Destination Transportation (FDT) program to reduce cost of transportation through the use of Government-Arranged Transportation utilizing Government contracts and rates. Offers should be submitted based on FOB Origin. For offerors whose shipments will orginate from outside the contiguous United States, the offeror's FOB Origin price shall include transportation to a contiguous United States location that the offeror selects based on cost effectiveness or other variables at the offeror's discretion. Additional information about FDT can be found at: http://www.dla.mil/FDTPI/ CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 27 PAGES SPE4A6-24-T-47P8 SECTION A CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 27 PAGES SPE4A6-24-T-47P8 SECTION B PR: 7007117744 NSN/MATERIAL:5305016298432 ITEM DESCRIPTION SCREW,CAP,HEXAGON H SCREW, CAP, HEXAGON HEAD P/N NAS90725-66 RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES MIL-STD-130N(1) DATED 16 NOV 2012. IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS) RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN Certificate of Quality Compliance (CoQC) Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. If CDRL-COQCCDRLs is missing from DLA Collaboration Folders (CFolders) they can also be viewed in Appendix 1 of the DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx CERTIFICATE OF CONFORMANCE PROCEDURES (FAR 52.246-15) ARE AUTHORIZED, UNLESS WITHELD BY A QUALITY ASSURANCE LETTER OF INSTRUCTION. RQ006: QUALITY CONFORMANCE INSPECTION REQUIREMENTS MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL NOT BE INTENTIONALLY ADDED TO(>,)> OR COME IN DIRECT CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 27 PAGES SPE4A6-24-T-47P8 SECTION B CONTACT WITH(>,)> ANY HARDWARE OR SUPPLIES FURNISHED UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS; AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA. PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR MERCURY COMPOUND. (IAW NAVSEA 5100-003D). ENGINEERING NOTES: /1/ THE THREADS SHALL BE IN ACCORDANCE WITH FED-STD-H28/2. ACCEPTABILITY OF SCREW THREADS SHALL BE IN ACCORDANCE WITH FED-STD-H28/20, SYSTEM 21. (2) THE THREAD LENGTH SHALL BE IN ACCORDANCE WITH ASME B18.2.1. (3) DIMENSIONS IN INCHES AND APPLY AFTER FINISH UNLESS OTHERWISE SPECIFIED. /4/ BASED ON MINIMUM ULTIMATE TENSILE STRENGTH OF 120 KSI FOR DIAMETERS THRU 1.0000 INCH; 105 KSI FOR 1.1250 INCH THRU 1.5000 INCH DIAMETERS; 90 KSI FOR DIAMETERS OVER 1.5000 INCHES. TENSILE STRENGTHS ARE CALCULATED BY THE STRESS AREAS INDICATED IN SCREWTHREAD STANDARDS FOR FEDERAL SERVICES, HANDBOOK H28. (5) UNLESS OTHERWISE SPECIFIED HEREIN, REFERENCED DOCUMENTS SHALL BE THE ISSUE IN EFFECT ON DATE OF MANUFACTURE. HOWEVER, EXISTING MATERIAL INVENTORY CERTIFIED TO A PREVIOUS REVISION OF THE APPLICABLE MATERIAL SPECIFICATION(S) IS ACCEPTABLE FOR USE UNTIL DEPLETION. /6/ HEADS SHALL BE MARKED IN ACCORDANCE WITH MIL-HDBK-131. RAISED MARKINGS ARE PREFERRED, STAMPINGS ARE ACCEPTABLE (7) SCREWS LESS THAN THREE DIAMETERS IN LENGTH SHALL MEET MINIMUM AND MAXIMUM HARDNESS VALUES AS SPECIFIED IN PROCUREMENT SPECIFICATION AND SHALL BE THE ONLY MECHANICAL PROPERTY REQUIREMENT FOR ACCEPTANCE OF THESE SIZES. (8) UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED. (9) THIS STANDARD TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. (10) DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994. (11) SUPERSEDES: MS35289, MS35291, MS35293, MS35295 IN PART, MS35297 AND MS35299; (BCAX2, 2.1, 3, 3.1, 3.2, 3.3, 4.2) IN PART; BCVX2, 2.1, 4, 4.1, 4.2, 4.3, 4.8, 4.9, 10; (BCVX2.2, 2.3, 2.8, 2.9, 10.2, 10.3) IN PART; BQLX1.2 IN PART, BQLX2, 3; BUBX2, 2.1, 2.2, 3, 3.1, 4, 4.1, 8, 8.1, 9, 9.1, 10, 10.1 (12) FOR DESCRIPTION OF STATUS NOTES SEE NAS380. CRITICAL APPLICATION ITEM IAW BASIC NON GOVT STD NASM90725 REVISION NR 03 DTD 05/31/2016 PART PIECE NUMBER: MS90725-66 IAW REFERENCE NON GOVT STD FF-S-85F REVISION NR F DTD 04/11/2023 PART PIECE NUMBER: CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0001 7007117744 0001 EA 20.000 NSN/MATERIAL:5305016298432 DELIVERY (IN DAYS):0080 DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 10 OF 27 PAGES SPE4A6-24-T-47P8 SECTION B PR: 7007117744 PRLI: 0001 CONT’D INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN PREP FOR DELIVERY: PKGING DATA - MIL-STD-2073-1E QUP:010 PRES MTHD:31 CLNG/DRY:1 PRESV MAT:00 WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0 UNIT CONT:BL OPI:M INTRMDTE CONT:E5 INTRMDTE CONT QTY:AAA PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:00 -00 No special marking PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT PARCEL POST ADDRESS: N50467 NAVAL NUCLEAR POWER TRAINING UNIT 1260 SNOW POINTE ROAD GOOSE CREEK SC 29445-8612 US SHIP BY FASTEST TRACEABLE MEANS. DO NOT USE PARCEL POST. FREIGHT SHIPPING ADDRESS: N50467 NAVAL NUCLEAR POWER TRAINING UNIT 1260 SNOW POINTE ROAD GOOSE CREEK SC 29445-8612 US M/F: (TCN) N5046740963481 RDD: PROJ: Z5E TP 2 SUPP ADD: YU0651 SIG: A FOR GOVERNMENT USE ONLY: (IPD) 05 DIC: A4A DIST: E9B ADV: FC: U4 Need Ship Date:00/00/0000 Original Required Delivery Date:04/11/2024 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * PRODUCTION LOT TEST APPROVAL - CONTRACTOR TESTING REQUIRED (REFER TO PROCUREMENT NOTE E03 FOR ADDITIONAL INFORMATION) CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0002 0000000000 EA 1.000 NSN/MATERIAL:S00000062 CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 11 OF 27 PAGES SPE4A6-24-T-47P8 SECTION B PR: PRLI: CONT’D DELIVERY (IN DAYS):0020 THIS LINE ITEM SIGNIFIES THE PRODUCTION LOT TEST REQUIREMENT (PLT). DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN Need Ship Date:00/00/0000 Original Required Delivery Date:00/00/0000 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *