PLATE, STRUCTURAL, AI

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 25 PAGES SPE4A5-24-T-167U SECTION A effectiveness or other variables at the offeror's discretion. Additional information about FDT can be found at: http://www.dla.mil/FDTPI/ CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 25 PAGES SPE4A5-24-T-167U SECTION B PR: 7006925661 NSN/MATERIAL:1560011502482 ITEM DESCRIPTION PLATE,STRUCTURAL,AI PLATE,STRUCTURAL,AI: RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF

THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR) RD002, COVERED DEFENSE INFORMATION APPLIES RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS) RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER) RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies. RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 25 PAGES SPE4A5-24-T-167U SECTION B (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. RT001: MEASURING AND TEST EQUIPMENT NOTE: A STABLE BASE DRAWING FORMS A PART OF THE DATA PACKAGE REQUIRED FOR PERFORMANCE AND AS SUCH WILL BE FORWARDED TO THE SUCCESSFUL OFFEROR WITHIN 30 DAYS AFTER AWARD OF THE CONTRACT. IF THE STABLE BASE DRAWING HAS NOT BEEN RECEIVED WITHIN 30 DAYS AFTER AWARD, NOTIFY THE PROCUREMENT CONTRACTING OFFICER. SPECIAL INSTRUCTIONS: WHEN THE USE OF STABLE BASE DRAWINGS ARE REQUIRED, THE FOLLOWING SHALL APPLY: A: STABILIZE BY ALLOWING THE STABLE BASE DRAWING TO REST FLAT AND UNRESTRAINED ON A FLAT SURFACE OVERNIGHT AT ROOM TEMPERATURE PRIOR TO USE. B. DO NOT STRETCH OR OTHERWISE APPLY STRESS. C. CHECK THE DIMENSIONAL ACCURACY OF THE GRID LINES. THE DIMENSION BETWEEN ADJACENT GRID LINES MUST BE WITHIN (+,-) 0.005 INCHES. THE GRID LINES SHALL BE MEASURED VERTICALLY, HORIZONTALLY AND DIAGONALLY, TO INSURE THAT THE GRIDS ARE WITHIN THE TOLERANCE OF (+,-) 0.005 INCHES. THE TOLERANCE IS ACCUMULATED OVER THE LENGTH AND WIDTH OF THE STABLE BASE DRAWING. D. TRAMMEL POINTS SHALL BE MEASURED TO WITHIN CENTERLINE 0.010. E. WHEN ROLLING STABLE BASE DRAWINGS, DO NOT ROLL LESS THAN 3 INCHES IN DIAMETER. F. IF THE ABOVE TOLERANCE POINTS PROVE TO BE INACCURATE, RECORD THE DISCREPANCIES IMMEDIATELY AND NOTIFY IN WRITING THE ADMINISTRATIVE CONTRACTING OFFICER (ACO). G. THE CONTRACTOR WILL BE ADVISED AT TIME OF ISSUANCE OF THE STABLE BASE DRAWING WHEN ITS RETURN IS REQUIRED. WHEN SO ADVISED, THE CONTRACTOR WILL: (1) RETURN THE STABLE BASE DRAWING (IF IT HAS NOT BEEN DAMAGED/DESTROYED IN THE MANUFACTURING PROCESS) BY TRACEABLE MEANS TO: DLA AVIATION ATTN: DLA AVIATION-VAAA (MYLAR SECTION) RICHMOND, VA 23297-5615 (2) CERTIFY TO THE ACO OR QUALITY ASSURANCE REPRESENTATIVE (QAR) THAT THE STABLE BASE DRAWING HAS EITHER BEEN RETURNED TO DSCR OR WAS DAMAGED/DESTROYED DURING MANUFACTURE. CERTIFICATION SHOULD REFERENCE THE CONTRACT NUMBER, DRAWING NUMBER AND SHEET. SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 25 PAGES SPE4A5-24-T-167U SECTION B AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. MIL-STD-130N(1) DATED 16 NOV 2012. IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY CRITICAL APPLICATION ITEM NORDAM GROUP LLC, THE 29957 P/N 35-8233-192 AERO COMPONENTS, LLC 59213 P/N 35-8233-192 THE BOEING COMPANY 81205 P/N 35-8233-192 D-J ENGINEERING INC 0C7H8 P/N 35-8233-192 CAMNETICS MANUFACTURING CORPORATION 0P657 P/N 35-8233-192 VOLUMATIC INC 1P642 P/N 35-8233-192 FMW, INC. 1QJK4 P/N 35-8233-192 MALONES CNC MACHINING INC 2V045 P/N 35-8233-192 INFINITY FABRICATION, INC. 06DM5 P/N 35-8233-192 IAW REFERENCE DRAWING NR 81205 35-8233/4 REVISION NR K DTD 07/10/2015 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 BAC5300 REVISION NR N DTD 12/05/2016 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 BAC5423 REVISION NR W DTD 09/02/1999 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 BAC5300-1 REVISION NR H DTD 06/23/2014 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 BAC5300-2 REVISION NR H DTD 09/15/2014 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 BAC5307 REVISION NR U DTD 11/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 35-8233 REVISION NR U DTD 10/05/2018 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 35-8233 REVISION NR U DTD 11/04/2020 PART PIECE NUMBER: 35-8233-192 IAW REFERENCE DRAWING NR 98748 20145214 REVISION NR A DTD 04/15/2022 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98748 20145214 REVISION NR A DTD 04/18/2022 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 13873 EI-011502482 REVISION NR DTD 11/03/2022 PART PIECE NUMBER: CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 25 PAGES SPE4A5-24-T-167U SECTION B CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0001 7006925661 0001 EA 1.000 NSN/MATERIAL:1560011502482 DELIVERY (IN DAYS):0189 DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN PREP FOR DELIVERY: PKGING DATA-QUP:001 IF MATERIAL IS CONSIDERED HAZARDOUS IAW FED-STD-313, PACKAGE IN ACCORDANCE WITH TQ REQUIREMENT IP025. IF THE MATERIAL IS NOT CONSIDERED HAZARDOUS, IN ACCORDANCE WITH FED-STD-313, THE MATERIAL SHALL BE COMMERCIALLY PACKAGED IN ACCORDANCE WITH ASTM D3951. All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT PARCEL POST ADDRESS: W62G2T W1A8 DLA DIST SAN JOAQUIN 25600 S CHRISMAN ROAD REC WHSE 57 TRACY CA 95304-5000 US FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND CONTRACT FREIGHT SHIPPING ADDRESS: W62G2T W1A8 DLA DIST SAN JOAQUIN 25600 S CHRISMAN ROAD REC WHSE 57 TRACY CA 95304-5000 US Need Ship Date:00/00/0000 Original Required Delivery Date:03/21/2024 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 10 OF 25 PAGES CONTINUED ON NEXT PAGE SPE4A5-24-T-167U