CLOTH, COATED

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 26 PAGES SPE1C1-24-Q-0309 SECTION B SUPPLY/SERVICE: PGC: 11150 CONT'D REQUIREMENTS FOR PROCUREMENT . . . . . . SECTION D - PACKAGING AND MARKING ALL WOOD PACKAGING MATERIAL (WPM) USED MUST MEET REQUIREMENTS OF INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES (ISPM) 15, "GUIDELINES FOR REGULATING WOOD PACKAGING MATERIALS IN INTERNATIONAL TRADE." DOD SHIPMENTS INSIDE AND OUTSIDE OF THE UNITED STATES MUST MEET ISPM 15 WHENEVER WPM IS USED TO SHIP DOD CARGO. ALL WPM SHALL COMPLY WITH THE OFFICIAL QUALITY CONTROL PROGRAM FOR HEAT TREATMENT (HT) OR KILN DRIED HEAT TREATMENT (KD HT) IN ACCORDANCE WITH AMERICAN LUMBER STANDARD COMMITTEE(>,)> INCORPORATED (ALSC) WOOD PACKAGING MATERIAL PROGRAM AND WPM ENFORCEMENT REGULATIONS (SEE HTTP://WWW.ALSC.ORG/). ALL WPM SHALL INCLUDE CERTIFICATION/QUALITY MARKINGS IN ACCORDANCE WITH THE ALSC STANDARD. MARKINGS SHALL BE PLACED IN AN UNOBSTRUCTED AREA THAT

WILL BE READILY VISIBLE TO INSPECTORS. PALLET MARKINGS SHALL BE APPLIED TO THE STRINGER OR BLOCK ON DIAGONALLY OPPOSITE SIDES OF THE PALLET AND BE CONTRASTING AND CLEARLY VISIBLE. ALL CONTAINERS SHALL BE MARKED ON A SIDE OTHER THAN THE TOP OR BOTTOM, CONTRASTING AND CLEARLY VISIBLE. ALL DUNNAGE USED IN CONFIGURING AND/OR SECURING THE LOAD SHALL ALSO COMPLY WITH ISPM 15 AND BE MARKED WITH AN ASLC APPROVED DUNNAGE STAMP. THE OVERALL PACKAGING AND PRESERVATION, IF APPLICABLE, SHALL CONFORM TO MIL-STD-2073-1E (WITH CHANGE 4 DATED 22 APRIL 2019) STANDARD PRACTICE FOR MILITARY PACKAGING FOR SHIPMENTS TO THE DEPARTMENT OF DEFENSE. UNIT CONTAINER: COATED CLOTH SHALL BE INDIVIDUALLY PACKAGED IN ANY BAG USED BY THE VENDOR. INTERMEDIATE CONTAINER: NOT REQUIRED; THE USE OF INTERMEDIATE PACKAGING IS ENCOURAGED PARTICULARLY WHEN SUCH USE ENHANCES HANDLING AND STORAGE. IF USED, VENDOR SHALL USE ANY SUITABLE FIBER BOX INCLUDED IN TABLE J-VII OF MIL-STD-2073-1E CHANGE 4 (PDF Pages 185/214) MAY BE USED (SEE ALSO J.4.9.1). EXTERIOR CONTAINER: SHALL BE STYLE: REGULAR SLOTTED BOX (RSC)(>,)> TYPE: CORRUGATED FIBERBOARD (CF), VARIETY DOUBLEWALL FIBERBOARD (DW), CLASS: DOMESTIC, GRADE: 275 WITH A SINGLE WALL LINER OR DW ECT GRADE 48, MADE TO THE REQUIREMENTS OF ASTM D5118M, STANDARD PRACTICE FOR FABRICATION OF FIBERBOARD SHIPPING BOXES TO INSURE MEETING THE REQUIREMENTS OF A PACK THAT WILL SUPPORT RE-TRANSPORT, STORAGE, STACKING, ETC. . THE PACKAGING CONTAINER SHALL BE SUFFICIENT TO PROVIDE PROTECTION DURING TRANSPORT AND STORAGE AND ARRIVE AT DESTINATION IN THE SAME CONDITION AS ORIGIN. PACKAGED COMPONENTS SHALL BE BULK PACKAGED IN A THAT WILL SUPPORT RE-TRANSPORT, STORAGE, STACKING, ETC. REFERENCE ASTM INTERNATIONAL DESIGNATION D1974M (STANDARD PRACTICE FOR METHODS OF CLOSING, SEALING, AND REINFORCING FIBERBOARD BOXES, WHICH DESCRIBES SEVERAL METHODS FOR CLOSING, SEALING, AND REINFORCING FIBERBOARD (SOLID AND CORRUGATED) SHIPPING BOXES USED FOR SHIPMENT. A PRESSURE SENSITIVE IDENTIFICATION LABEL SHALL ATTACH TO EACH PACKAGING BOX OF THE COMPONENT. THE PACKAGING CONTAINER SHALL BE SUFFICIENT TO PROVIDE PROTECTION DURING TRANSPORT AND STORAGE AND ARRIVE AT DESTINATION IN THE SAME CONDITION AS ORIGIN. SURFACE OF THE PALLET. WHEN SPECIFIED PALLETIZATION IS REQUIRED, COMPONENTS SHALL BE PALLETIZED ON A FOUR-WAY ENTRY PALLET IN ACCORDANCE WITH LOAD TYPE I OR IA, AS APPLICABLE, OF MIL-STD-147E, CHANGE 2 DATED 27 JUNE 2019. CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 26 PAGES SPE1C1-24-Q-0309 SECTION B SUPPLY/SERVICE: PGC: 11150 CONT'D THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL BONDING MATERIALS. PALLET LOADS SHALL CONTAIN THE SAME NUMBER OF CARTONS, OF IDENTICAL QUANTITIES, OF ONE NSN, TO THE MAXIMUM EXTENT POSSIBLE. PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE THAN ONE NSN. AT THE END OF A SIZE RUN, NO MORE THAN ONE CARTON PER NSN MAY BE SHORT OR OVER THE SPECIFIED QUANTITY. SAID CARTON SHALL BE CLEARLY MARKED "SHORT" OR "OVER". IN ADDITION TO SPECIAL MARKING REQUIRED(>,)> INTERIOR (UNIT) PACKS, INTERMEDIATE CONTAINERS(>,)> SHIPPING CONTAINERS AND PALLETIZED UNIT LOADS SHALL BE MARKED FOR SHIPMENT, STOWAGE, AND STORAGE IN ACCORDANCE WITH MIL-STD-129R CHANGE 2 DATED 27 SEPTEMBER 2019. GUIDANCE FOR THE REQUIRED IDENTIFICATION TEXT MARKINGS OF THE UNIT, INTERMEDIATE, AND EXTERIOR CONTAINERS ARE FOUND ON PAGES 26 TO 29 WITHIN MIL-STD-129R WITH CHANGE 2 DATED 27 SEPTEMBER 2019. . 7/19/2021 PARCEL POST ADDRESS: UY8615 ARIZONA INDUSTRIES FOR THE BLIND 515 N 51ST AVENUE NUMBER 130 DOCK 1 PHOENIX AZ 85043 US FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND CONTRACT FREIGHT SHIPPING ADDRESS: UY8615 ARIZONA INDUSTRIES FOR THE BLIND 515 N 51ST AVENUE NUMBER 130 DOCK 1 PHOENIX AZ 85043 US GOVT USE External External External Customer RDD/ ITEM PR PRLI PR PRLI Material Need Ship Date . 0001 7007087611 0001 N/A N/A N/A 08/01/2024 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 7 OF 26 PAGES CONTINUED ON NEXT PAGE SPE1C1-24-Q-0309 SECTION A - SOLICITATION/CONTRACT FORM 52.204-16 COMMERCIAL AND GOVERNMENT ENTITY CODE REPORTING (AUG 2020) FAR SECTION C - SPECIFICATIONS/SOW/SOO/ORD C03 CONTRACTOR RETENTION OF SUPPLY CHAIN TRACEABILITY DOCUMENTATION (MAR 2023) C01 SUPERSEDED PART NUMBERED ITEMS (SEP 2016) SECTION E - INSPECTION AND ACCEPTANCE 52.246-2 INSPECTION OF SUPPLIES FIXED PRICE (AUG 1996) FAR 52.246-15 CERTIFICATE OF CONFORMANCE (APR 1984) FAR As prescribed in 46.315, insert the following clause in solicitations and contracts for supplies or services when the conditions in 46.504 apply: (a) When authorized in writing by the cognizant Contract Administration Office (CAO), the Contractor shall ship with a Certificate of Conformance any supplies for which the contract would otherwise require inspection at source. In no case shall the Government's right to inspect supplies under the inspection provisions of this contract be prejudiced. Shipments of such supplies will not be made under this contract until use of the Certificate of Conformance has been authorized in writing by the CAO, or inspection and acceptance have occurred. (b) The Contractor's signed certificate shall be attached to or included on the top copy of the inspection or receiving report distributed to the payment office or attached to the CAO copy when contract administration (Block 10 of the DD Form 250) is performed by the Defense Contract Administration Services. In addition, a copy of the signed certificate shall also be attached to or entered on copies of the inspection or receiving report accompanying the shipment. (c) The Government has the right to reject defective supplies or services within a reasonable time after delivery by written notification to the Contractor. The Contractor shall in such event promptly replace, correct, or repair the rejected supplies or services at the Contractor's expense. (d) The certificate shall read as follows: “I certify that on , the furnished the supplies or services called for by Contract No. via on in accordance with all applicable requirements. I further certify that the supplies or services are of the quality specified and conform in all respects with the contract requirements, including specifications, drawings, preservation, packaging, packing, marking requirements, and physical item identification (part number), and are in the quantity shown on this or on the attached acceptance document.” Date of Execution: Signature: Title: (End of clause)