PRODUCTION LOT TESTING

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 27 PAGES SPE4A5-24-T-167V SECTION A 6, THE OFFEROR, BY SUBMISSION OF ITS QUOTATION, REPRESENTS IT WILL NOT PROVIDE COVERED TELECOMMUNICATIONS EQUIPMENT OR SERVICES TO THE GOVERNMENT IN THE PERFORMANCE OF ANY AWARD RESULTING FROM THIS SOLICITATION, IN ACCORDANCE WITH PARAGRAPH (d) OF THE CLAUSE AT FAR 52.204-24, REPRESENTATION REGARDING CERTAIN TELECOMMUNICATIONS AND VIDEO SURVEILLANCE SERVICES OR EQUIPMENT, OR IN ACCORDANCE WITH ITS EXISTING REPRESENTATION IN PARAGRAPH (c) OF THE PROVISION AT DFARS 252.204-7016, COVERED DEFENSE TELECOMMUNICATIONS EQUIPMENT OR SERVICES – REPRESENTATION. Caution Notice: Offerors are required to comply with domestic material restrictions. The Berry Amendment, the Buy American Act, and other domestic material restrictions may apply. Offerors are instructed to refer to the solicitation clauses related to foreign sourcing for more information on applicability. The

Berry Amendment threshold has been reduced to $150,000 and vendors must carefully review related clauses DFARS 252.225-7006, 252.225-7012, and 252.225-7015 for applicability requirements. If your offer is based on a non-domestic material, you are required to provide disclosure information in your quote and/or through written notification to the point of contact listed in the solicitation. DoD Class Deviation 2023-O0001: A small business joint venture offeror must submit, with its offer, the representation required in paragraph (c) of FAR solicitation provision 52.212-3, Offeror Representations and Certifications-Commercial Products and Commercial Services, and paragraph (c) of FAR solicitation provision 52.219-1, Small Business Program Representations, in accordance with 52.204-8(d) and 52.212- 3(b) for the following categories: (A) Small business; (B) Service-disabled veteran-owned small business; (C) Women-owned small business (WOSB) under the WOSB Program; (D) Economically disadvantaged women-owned small business under the WOSB Program; or (E) Historically underutilized business zone small business. CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 27 PAGES SPE4A5-24-T-167V SECTION A Contractors shall not provide parts and supplies made using additive manufacturing (AM), unless AM is specifically authorized in the solicitation/contract. See procurement note L31. Procurement History for NSN/FSC:011959303/3040 CAGE Contract Number Quantity Unit Cost AWD Date Surplus Material . 0BVP9 SPE7L219P0460P00001 4.000 6582.43000 20190307 N 61174 N0038306G067BYMNC02 4.000 1873.20000 20070817 N 26512 N0038300G027BUB5K 1.000 4224.84000 20050331 N 26512 N0038300G027BUB2W 1.000 4220.69000 20031016 N 26512 N0038300G027BUB96 1.000 3281.95000 20030520 N 26512 N0038394GM114UB23 4.000 2421.66000 19960223 N 26512 N0038388GM1003005 14.000 313.14000 19890714 N 26512 N0038385G5K071156 9.000 318.54000 19850318 N This solicitation is being issued under the First Destination Transportation (FDT) program to reduce cost of transportation through the use of Government-Arranged Transportation utilizing Government contracts and rates. Offers should be submitted based on FOB Origin. For offerors whose shipments will orginate from outside the contiguous United States, the offeror's FOB Origin price shall include transportation to a contiguous United States location that the offeror selects based on cost effectiveness or other variables at the offeror's discretion. Additional information about FDT can be found at: http://www.dla.mil/FDTPI/ CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 27 PAGES SPE4A5-24-T-167V SECTION B PR: 7006925606 NSN/MATERIAL:3040011959303 ITEM DESCRIPTION CONNECTING LINK, RIG CONNECTING LINK, RIGID RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR) RD002, COVERED DEFENSE INFORMATION APPLIES RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER) RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies. RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 27 PAGES SPE4A5-24-T-167V SECTION B export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. RQ039: Non-Tailored Higher-Level Quality Requirements (SAE AS9100) for Manufacturers and Non-Manufacturers MIL-STD-130N(1) DATED 16 NOV 2012. IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY Contractor first article/preproduction approval testing required. Use DI-NDTI-80809B in preparation of the first article report. Current revision of MIL-HDBK-831 may also be used for report format guidance. First article testing shall be conducted IAW applicable drawings and drawing notes, specification, engineering instructions and specific requirements set forth in the contract. Additionally, 100% dimensional characteristics check shall be performed and results provided to the contracting officer. The first article offered must be manufactured at the facilities in which production quantities are procured under the contract. Contractor shall provide a statement along with objective evidence that test and production items meet the material and process requirements of the contract. If applicable, DD form 1423 documentation shall be provided as required. Unless F.A.T sample(s) is degraded or destroyed in testing or submitted for government fit, form, function verification (when specified by contract), the F.A.T. samples(s) may be deliverable with the last production run of the contract. Additional Wide Area Workkflow (WAWF) instructions for contractor first article test CLIN: The contractor shall code the receiving report for contractor first article test CLIN in WAWF as follows: A. Inspection at origin (source)- Enter the DCMA DODAAC listed on page 1 of the contract. B. Acceptance at destination- Enter the issue by office DODAAC listed C. Ship to code - Enter the issue by office DODAAC listed on page 1 of the contract. SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. THIS IS A NAVY IDENTIFIED CRITICAL SAFETY ITEM (CSI). ALL REQUESTS FOR WAIVERS OR DEVIATIONS MUST BE FORWARDED TO THE DSC CONTRACTING OFFICER FOR REVIEW AND APPROVAL. . ALL ITEMS OF SUPPLY SHALL BE MARKED IAW MIL-STD-129. IN ADDITION, EACH UNIT PACK WILL BE MARKED WITH LOT AND SERIAL NUMBER (IF AVAILABLE), CONTRACTOR'S CAGE CODE, ACTUAL MANUFACTURER'S CAGE CODE AND PART NUMBER. CRITICAL APPLICATION ITEM CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 27 PAGES SPE4A5-24-T-167V SECTION B NORTHROP GRUMMAN SYSTEMS CORPORATION 79RG9 P/N 123C10221-601 IAW REFERENCE DRAWING NR 26512 GS30BF REVISION NR AF DTD 09/22/2015 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 26512 GS30A REVISION NR AE DTD 05/31/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 26512 123C10221 REVISION NR E DTD 10/28/1989 PART PIECE NUMBER: 123C10221-601 IAW REFERENCE DRAWING NR 26512 GSS4710 REVISION NR F DTD 05/17/2001 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 26512 GS31AB REVISION NR AR DTD 10/13/2015 PART PIECE NUMBER: IAW REFERENCE QAP 26512 CDRL011959303 REVISION NR DTD 04/28/2016 PART PIECE NUMBER: IAW REFERENCE QAP 26512 QAP011959303 REVISION NR DTD 03/18/2016 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 26512 123C10221 REVISION NR E DTD 10/28/1985 PART PIECE NUMBER: IAW REFERENCE QAP 13873 QAP-106 REVISION NR B DTD 07/09/2012 PART PIECE NUMBER: CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0001 7006925606 0001 EA 5.000 NSN/MATERIAL:3040011959303 DELIVERY (IN DAYS):0544 DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN PREP FOR DELIVERY: PKGING DATA - MIL-STD-2073-1E QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00 WRAP MAT:00 CUSH/DUNN MAT:GT CUSH/DUNN THKNESS:B UNIT CONT:E5 OPI:M INTRMDTE CONT:E5 INTRMDTE CONT QTY:AAA PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:ZZ -ZZ Special Requirements PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 10 OF 27 PAGES SPE4A5-24-T-167V SECTION B PR: 7006925606 PRLI: 0001 CONT’D PARCEL POST ADDRESS: SW3218 DLA DISTRIBUTION SAN DIEGO 3581 CUMMINGS ROAD BLDG 3581 SAN DIEGO CA 92136-3581 US FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND CONTRACT FREIGHT SHIPPING ADDRESS: SW3218 DLA DISTRIBUTION SAN DIEGO 3581 CUMMINGS ROAD BLDG 3581 SAN DIEGO CA 92136-3581 US Need Ship Date:00/00/0000 Original Required Delivery Date:03/07/2024 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * CONTRACTOR FIRST ARTICLE TEST - THE NUMBER OF UNITS SHOWN SIGNIFIES THE TEST REQUIREMENT. SEE FAR CLAUSE 52.209-3 CITED IN SECTION A OF THIS SOLICITATION FOR THE ACTUAL QUANTITY REQUIRED. CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0002 0000000000 EA 1.000 NSN/MATERIAL:0001S00000053 DELIVERY (IN DAYS):0090 THIS LINE ITEM SIGNIFIES THE FIRST ARTICLE TEST REQUIREMENT (FAT). SEE CLAUSES FOR INFORMATION CONCERNING THE FAT REQUIREMENT. OFFERS THAT DO NOT CITE A PRICE FOR THIS LINE ITEM SHALL BE EVALUATED UNDER THE ASSUMPTION THAT THERE IS NO SEPARATE CHARGE FOR THE FAT. IN THE EVENT THE FAT REQUIREMENT IS WAIVED, NO AWARD WILL BE MADE FOR THIS LINE ITEM. THE NUMBER OF UNITS SHOWN APPEARS AS “1 EA”. THIS QUANTITY SIGNIFIES THE TEST REQUIREMENT. OFFERORS WILL FIND THE ACTUAL QUANTITY REQUIRED BY THE GOVERNMENT FOR THE FAT LINE ITEM PER FAR 52.209-3 OR 52.209-4 IN SECTION A OF THIS SOLICITATION. DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN Need Ship Date:00/00/0000 Original Required Delivery Date:00/00/0000 CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 11 OF 27 PAGES SPE4A5-24-T-167V SECTION B PR: PRLI: CONT’D * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * PRODUCTION LOT TEST APPROVAL - CONTRACTOR TESTING REQUIRED (REFER TO PROCUREMENT NOTE E03 FOR ADDITIONAL INFORMATION) CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0003 0000000000 EA 1.000 NSN/MATERIAL:S00000062 DELIVERY (IN DAYS):0514 THIS LINE ITEM SIGNIFIES THE PRODUCTION LOT TEST REQUIREMENT (PLT). DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN Need Ship Date:00/00/0000 Original Required Delivery Date:00/00/0000 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *