FAIRING, AIRCRAFT

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 28 PAGES SPE4A7-24-T-269N SECTION A 52.204-24, REPRESENTATION REGARDING CERTAIN TELECOMMUNICATIONS AND VIDEO SURVEILLANCE SERVICES OR EQUIPMENT, OR IN ACCORDANCE WITH ITS EXISTING REPRESENTATION IN PARAGRAPH (c) OF THE PROVISION AT DFARS 252.204-7016, COVERED DEFENSE TELECOMMUNICATIONS EQUIPMENT OR SERVICES – REPRESENTATION. Caution Notice: Offerors are required to comply with domestic material restrictions. The Berry Amendment, the Buy American Act, and other domestic material restrictions may apply. Offerors are instructed to refer to the solicitation clauses related to foreign sourcing for more information on applicability. The Berry Amendment threshold has been reduced to $150,000 and vendors must carefully review related clauses DFARS 252.225-7006, 252.225-7012, and 252.225-7015 for applicability requirements. If your offer is based on a non-domestic material, you are required to

provide disclosure information in your quote and/or through written notification to the point of contact listed in the solicitation. DoD Class Deviation 2023-O0001: A small business joint venture offeror must submit, with its offer, the representation required in paragraph (c) of FAR solicitation provision 52.212-3, Offeror Representations and Certifications-Commercial Products and Commercial Services, and paragraph (c) of FAR solicitation provision 52.219-1, Small Business Program Representations, in accordance with 52.204-8(d) and 52.212- 3(b) for the following categories: (A) Small business; (B) Service-disabled veteran-owned small business; (C) Women-owned small business (WOSB) under the WOSB Program; (D) Economically disadvantaged women-owned small business under the WOSB Program; or (E) Historically underutilized business zone small business. Contractors shall not provide parts and supplies made using additive manufacturing (AM), unless AM is specifically authorized in the solicitation/contract. See procurement note L31. CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 28 PAGES SPE4A7-24-T-269N SECTION A Procurement History for NSN/FSC:004582729/1560 CAGE Contract Number Quantity Unit Cost AWD Date Surplus Material . 419Y2 SPM4A707MC288P00001 14.000 875.00000 20070907 N 9U679 SPM4A707M0241 14.000 878.00000 20061010 N 9U679 SP040006M0847 10.000 1008.02000 20060120 N 9U679 SP047004W6041 3.000 2775.00000 20040901 N 59213 SP047004MAA32 3.000 8020.70000 20031110 N 34336 F3460183G1755SA9800 18.000 122.90000 19840207 N This solicitation is being issued under the First Destination Transportation (FDT) program to reduce cost of transportation through the use of Government-Arranged Transportation utilizing Government contracts and rates. Offers should be submitted based on FOB Origin. For offerors whose shipments will orginate from outside the contiguous United States, the offeror's FOB Origin price shall include transportation to a contiguous United States location that the offeror selects based on cost effectiveness or other variables at the offeror's discretion. Additional information about FDT can be found at: http://www.dla.mil/FDTPI/ CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 28 PAGES SPE4A7-24-T-269N SECTION B PR: 7007302022 NSN/MATERIAL:1560004582729 ITEM DESCRIPTION FAIRING,AIRCRAFT FAIRING, AIRCRAFT RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. RD002, COVERED DEFENSE INFORMATION APPLIES RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS) RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS) RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER) CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 28 PAGES SPE4A7-24-T-269N SECTION B RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES P/N 4J32470-108B CRITICAL APPLICATION SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. MIL-STD-130N(1) DATED 16 NOV 2012. IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY Government First Article Preproduction approval required. Testing will be in accordance with applicable drawings, specifications and/or Engineering instructions. The first article offered shall be manufactured at the facilities in which production quantities are procured and produced under this contract. When submitting the first article(s) for government testing, a copy of the contract and all applicable drawings, specifications, engineering instructions, certifications, and inspection sheets shall be provided. Upon receipt and evaluation of the test report from the responsible government testing location, the contracting officer will provide final notification to the manufacturer. Any questions or concerns regarding the first article test requirements must be submitted through the contracting officer. Additional Wide Area Workflow (WAWF) instructions for government first article test CLIN: The contractor shall code the receiving report for government first article test CLIN in WAWF as Follows: A: Inspection at origin (Source) - Enter the DCMA office DODAAC listed on page 1 of the contract. B: Acceptance by other - Enter the issue by office DODAAC listed on page 1 of the contract. C: Ship to code - Enter the DODAAC of the test facility listed for the government first article test CLIN in the contract (See FAR Clause 52.209-4). FIRST ARTICLE TEST MARKING INSTRUCTIONS: FAT sample(s) packaging shall be clearly marked "FIRST ARTICLE TEST EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contrasting color to the packaging. Marking shall be located adjacent to the Package Shipping Label side and on at least one additional side of the package. NOTE: ENGINEERING NOTES #1, 2, 3, 10, & 12 APPLIES I/A/W 200415485. POT DATA: L 98897 4J32470 & EO's E S C FAIRING-UPPER Dove, John C 19 MAR 2024 -108B. EO's 2005C0001-R & 2021C0002-R. L 98897 4J32470 MY B S C FAIRING-UPPER Dove, John C 19 MAR 2024 MYLAR 98897 DS5025 BA S C DRAWING STANDARD CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 28 PAGES SPE4A7-24-T-269N SECTION B L 98897 4R23200 S C MASTER DIMENSIONS DATA - WING OUTER WING TRAILING L 98897 4R22200 A S C WING, INNER WING TRAILING EDGE (EO 2005C0001-R) L 98897 STP63-001 & EO W S C MARKING PARTS AND ASSEMBLIES FOR IDENTIFICATION A EO 2021C0001-R. L 98897 DS30000 Dove, John C 19 MAR 2024 SUPERSEDED. USE 2020111556. L 98752 2020111556 A S C C-5 FINISH CODE INTERPRETATION USE IN LIEU OF DS30000 PER EO 2021C0004-R L 98897 STP59-007 F S D POLYURETHANE SYSTEM MILPRF- 23377-MIL-PRF-85285 FINISH -FA & 71. L 98897 STP60-401 & EO J S C APPLICATION OF CASTING RESIN AND SEALANTS TO BONDE EO 2012C0001-R. L 98897 4J00002 AC S C AERODYNAMIC SMOOTHNESS REQUIREMENTS - EXTERNAL SU L 98897 STM28-003 & EO C S C SANDWICH STRUCTURE WITH COMPRESSED HONEYCOMB CORE(>,)> EO 2018C0001-R. L 98752 200415485 E S A General Engineering Notes Dove, John C 19 MAR 2024 NOTES 1,3,6,10 & 12 APPLY. STANDARD ENGINEERING TEXT SPARES CONFIGURATION: OMIT ATTACHMENT HOLES TO NEXT HIGHER ASSEMBLY. DIGITAL MYLAR DATA EXISTS FOR THIS NSN, AND WILL BE INCLUDED IN THE TECHNICAL DATA PACKAGE PROVIDED BY DLA. IF UNABLE TO USE THE DATA IN THE DIGITAL FORMAT PROVIDED, THE CONTRACTOR WILL BE RESPONSIBLE FOR HAVING THE DATA CONVERTED TO THE NECESSARY FORMAT (I.E. MYLAR FILM), THROUGH A THIRD PARTY AND BEAR THE ASSOCIATED COSTS WHEN CONVERTING FROM DIGITAL TO STABLE BASED FORMAT, THE DIGITAL MYLAR SHALL BE PLOTTED ON STABLE BASE MATERIAL, WHILE MAINTAINING THE DIMENSIONAL ACCURACY DEMANDS OF THE UNDIMENSIONED DRAWING. THIS INCLUDES BUT IS NOT LIMITED TO: VERIFY THE PLOT OF THE MYLAR(S) FOR DIMENSIONAL ACCURACY AS OUTLINED IN ASME Y14.31. ACCURACY SHALL BE DETERMINED VERTICALLY, HORIZONTALLY AND DIAGONALLY. ENSURE THAT THE INDIVIDUAL GRID UNITS ARE WITHIN THE TOLERANCE OF (+,-) 0.005 INCHES AND (+,-) 0.007 INCHES DIAGONALLY. TOTAL GRID TOLERANCE SHALL BE (+,-) 0.010 INCHES AND (+,-) 0.014 INCHES DIAGONALLY. DRAWINGS WITH DIMENSIONAL ACCURACY POINTS SUCH AS TRAMMEL POINTS SHALL BE MEASURED TO WITHIN CENTERLINE (+,-) 0.010 INCHES AND (+,-) 0.014 INCHES DIAGONALLY. REGISTRATION MARKS SUCH AS THOSE USED ON CIRCUIT CARDS SHALL BE MEASURED TO WITHIN (+,-) 0.005 INCHES AND (+,-) 0.007 INCHES DIAGONALLY. IAW BASIC DRAWING NR 98897 4J32470 REVISION NR E DTD 07/07/1986 PART PIECE NUMBER: 4J32470-108B IAW REFERENCE DRAWING NR 98897 STP59-007 REVISION NR F DTD 09/07/2005 PART PIECE NUMBER: CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 10 OF 28 PAGES SPE4A7-24-T-269N SECTION B IAW REFERENCE DRAWING NR 98897 STP59-204 REVISION NR B DTD 10/14/1983 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 STP58-408 REVISION NR M DTD 06/15/2015 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 STP59-405 REVISION NR DTD 11/30/1966 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 STP60-401 REVISION NR J DTD 08/15/1990 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 DS30000 REVISION NR AA DTD 07/18/2016 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 STP63-001 REVISION NR J DTD 10/22/1984 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 DS5025 REVISION NR BA DTD 05/11/2023 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 STP51-302V11 REVISION NR AA DTD 03/01/1988 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 STP63-001 REVISION NR W DTD 04/28/2023 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 13873 004582729-06055 REVISION NR DTD 02/24/2006 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 4J00002 REVISION NR AC DTD 11/07/1988 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 4J32470 REVISION NR E DTD 02/03/2021 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 4R22200 REVISION NR A DTD 10/19/1967 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 4R23200 REVISION NR DTD 11/02/1967 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 STM28-003 REVISION NR C DTD 06/09/1983 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 STP51-302 REVISION NR AF DTD 04/28/2022 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 DS30000 REVISION NR T DTD 10/19/1998 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 4J32470/2 CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 11 OF 28 PAGES SPE4A7-24-T-269N SECTION B REVISION NR B DTD 01/01/1939 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98752 200415485 REVISION NR E DTD 01/30/2020 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98752 2020111556 REVISION NR A DTD 08/22/2023 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98752 2020111556 REVISION NR A DTD 10/04/2023 PART PIECE NUMBER: CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0001 7007302022 0001 EA 4.000 NSN/MATERIAL:1560004582729 DELIVERY (IN DAYS):0522 DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN PREP FOR DELIVERY: PKGING DATA-QUP:001 IF MATERIAL IS CONSIDERED HAZARDOUS IAW FED-STD-313, PACKAGE IN ACCORDANCE WITH TQ REQUIREMENT IP025. IF THE MATERIAL IS NOT CONSIDERED HAZARDOUS, IN ACCORDANCE WITH FED-STD-313, THE MATERIAL SHALL BE COMMERCIALLY PACKAGED IN ACCORDANCE WITH ASTM D3951. All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT PARCEL POST ADDRESS: SW3119 DLA DISTRIBUTION WARNER ROBINS 455 BYRON STREET BLDG 376 ROBINS A F B GA 31098-1887 US FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND CONTRACT FREIGHT SHIPPING ADDRESS: SW3119