BEAM, AIRCRAFT

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 29 PAGES SPE4A7-24-T-186L SECTION A THE OFFEROR, BY SUBMISSION OF ITS QUOTATION, REPRESENTS IT WILL NOT PROVIDE COVERED TELECOMMUNICATIONS EQUIPMENT OR SERVICES TO THE GOVERNMENT IN THE PERFORMANCE OF ANY AWARD RESULTING FROM THIS SOLICITATION, IN ACCORDANCE WITH PARAGRAPH (d) OF THE CLAUSE AT FAR 52.204-24, REPRESENTATION REGARDING CERTAIN TELECOMMUNICATIONS AND VIDEO SURVEILLANCE SERVICES OR EQUIPMENT, OR IN ACCORDANCE WITH ITS EXISTING REPRESENTATION IN PARAGRAPH (c) OF THE PROVISION AT DFARS 252.204-7016, COVERED DEFENSE TELECOMMUNICATIONS EQUIPMENT OR SERVICES – REPRESENTATION. Caution Notice: Offerors are required to comply with domestic material restrictions. The Berry Amendment, the Buy American Act, and other domestic material restrictions may apply. Offerors are instructed to refer to the solicitation clauses related to foreign sourcing for more information on applicability. The

Berry Amendment threshold has been reduced to $150,000 and vendors must carefully review related clauses DFARS 252.225-7006, 252.225-7012, and 252.225-7015 for applicability requirements. If your offer is based on a non-domestic material, you are required to provide disclosure information in your quote and/or through written notification to the point of contact listed in the solicitation. DoD Class Deviation 2023-O0001: A small business joint venture offeror must submit, with its offer, the representation required in paragraph (c) of FAR solicitation provision 52.212-3, Offeror Representations and Certifications-Commercial Products and Commercial Services, and paragraph (c) of FAR solicitation provision 52.219-1, Small Business Program Representations, in accordance with 52.204-8(d) and 52.212- 3(b) for the following categories: (A) Small business; (B) Service-disabled veteran-owned small business; (C) Women-owned small business (WOSB) under the WOSB Program; (D) Economically disadvantaged women-owned small business under the WOSB Program; or (E) Historically underutilized business zone small business. CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 29 PAGES SPE4A7-24-T-186L SECTION A Contractors shall not provide parts and supplies made using additive manufacturing (AM), unless AM is specifically authorized in the solicitation/contract. See procurement note L31. Procurement History for NSN/FSC:011201868/1560 CAGE Contract Number Quantity Unit Cost AWD Date Surplus Material . 1XKR3 SPE4A720P9181 1.000 3500.00000 20200420 N 1XKR3 SPE4A719P8676P00002 1.000 2787.50000 20190402 N 1XKR3 SPE4A719P6871P00001 2.000 2787.50000 20190225 N 5Z8U5 SPE4A718P3324P00001 2.000 2500.00000 20171222 N 1XKR3 SPE4A715M3085 5.000 2997.00000 20150122 N 1XKR3 SPE4A713M8130P00001 2.000 3120.00000 20130402 N 1XKR3 SPE4A713M8088 2.000 3120.00000 20130401 N 05DN8 SP047504MBG31 20.000 1200.00000 20040123 N 8Z052 F4260091G7544089900 3.000 1738.82000 19950209 N 8Z052 F4260083C4011 2.000 363.77000 19830523 N This solicitation is being issued under the First Destination Transportation (FDT) program to reduce cost of transportation through the use of Government-Arranged Transportation utilizing Government contracts and rates. Offers should be submitted based on FOB Origin. For offerors whose shipments will orginate from outside the contiguous United States, the offeror's FOB Origin price shall include transportation to a contiguous United States location that the offeror selects based on cost effectiveness or other variables at the offeror's discretion. Additional information about FDT can be found at: http://www.dla.mil/FDTPI/ CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 29 PAGES SPE4A7-24-T-186L SECTION B PR: 7006804112 NSN/MATERIAL:1560011201868 ITEM DESCRIPTION BEAM,AIRCRAFT BEAM,AIRCRAFT RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RD002, COVERED DEFENSE INFORMATION APPLIES RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS) RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER) RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies. RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 29 PAGES SPE4A7-24-T-186L SECTION B been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. RT001: MEASURING AND TEST EQUIPMENT DIGITAL MYLAR DATA EXISTS FOR THIS NSN, AND WILL BE INCLUDED IN THE TECHNICAL DATA PACKAGE PROVIDED BY DLA. IF UNABLE TO USE THE DATA IN THE DIGITAL FORMAT PROVIDED, THE CONTRACTOR WILL BE RESPONSIBLE FOR HAVING THE DATA CONVERTED TO THE NECESSARY FORMAT (I.E. MYLAR FILM), THROUGH A THIRD PARTY AND BEAR THE ASSOCIATED COSTS WHEN CONVERTING FROM DIGITAL TO STABLE BASED FORMAT, THE DIGITAL MYLAR SHALL BE PLOTTED ON STABLE BASE MATERIAL, WHILE MAINTAINING THE DIMENSIONAL ACCURACY DEMANDS OF THE UNDIMENSIONED DRAWING. THIS INCLUDES BUT IS NOT LIMITED TO: VERIFY THE PLOT OF THE MYLAR(S) FOR DIMENSIONAL ACCURACY AS OUTLINED IN ASME Y14.31. ACCURACY SHALL BE DETERMINED VERTICALLY, HORIZONTALLY AND DIAGONALLY. ENSURE THAT THE INDIVIDUAL GRID UNITS ARE WITHIN THE TOLERANCE OF (+,-) 0.005 INCHES AND (+,-) 0.007 INCHES DIAGONALLY. TOTAL GRID TOLERANCE SHALL BE (+,-) 0.010 INCHES AND (+,-) 0.014 INCHES DIAGONALLY. DRAWINGS WITH DIMENSIONAL ACCURACY POINTS SUCH AS TRAMMEL POINTS SHALL BE MEASURED TO WITHIN CENTERLINE (+,-) 0.010 INCHES AND (+,-) 0.014 INCHES DIAGONALLY. REGISTRATION MARKS SUCH AS THOSE USED ON CIRCUIT CARDS SHALL BE MEASURED TO WITHIN (+,-) 0.005 INCHES AND (+,-) 0.007 INCHES DIAGONALLY. SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. MIL-STD-130N(1) DATED 16 NOV 2012. IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY Government First Article Preproduction approval required. Testing will be in accordance with applicable drawings, specifications and/or Engineering instructions. The first article offered shall be manufactured at the facilities in which production quantities are procured and produced under this contract. When submitting the first article(s) for government testing, a copy of the contract and all applicable drawings, specifications, engineering instructions, certifications, and inspection sheets shall be provided. Upon receipt and evaluation of the test report from the responsible government testing location, the contracting officer will provide final notification to the manufacturer. Any questions or concerns regarding the first article test requirements must be submitted through the contracting officer. Additional Wide Area Workflow (WAWF) instructions for government first article test CLIN: The contractor shall code the receiving report for government first article test CLIN in WAWF as Follows: A: Inspection at origin (Source) - Enter the DCMA office DODAAC listed on page 1 of the contract. B: Acceptance by other - Enter the issue by office DODAAC listed on page 1 of the contract. C: Ship to code - Enter the DODAAC of the test facility listed for the CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 29 PAGES SPE4A7-24-T-186L SECTION B government first article test CLIN in the contract (See FAR Clause 52.209-4). FIRST ARTICLE TEST MARKING INSTRUCTIONS: FAT sample(s) packaging shall be clearly marked "FIRST ARTICLE TEST EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contrasting color to the packaging. Marking shall be located adjacent to the Package Shipping Label side and on at least one additional side of the package. EXCEPTIONS: SEE TECH DATA PACKAGE DOCUMENT EI-011201868 FOR ENGINEERING INSTRUCTIONS FOR THIS ITEM CRITICAL APPLICATION ITEM IAW BASIC DRAWING NR 81755 16L113 REVISION NR AG DTD 11/30/2001 PART PIECE NUMBER: 16L113-805 IAW REFERENCE DRAWING NR 81755 16Z001 REVISION NR AK DTD 03/11/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 16L113ISS096 REVISION NR V DTD 03/16/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 16L113ISS046 REVISION NR V DTD 12/03/2001 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 16PR070 REVISION NR T DTD 08/13/2018 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 FMS-3002 REVISION NR A DTD 07/21/1980 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 FPS-3001 REVISION NR H DTD 03/15/2019 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 NDTS-1502 REVISION NR N DTD 10/04/2021 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 FQPL-3017 REVISION NR 10 DTD 11/29/1995 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 FQPL-NDTS-1101 REVISION NR 28 DTD 02/13/2023 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 NDTS-1500 REVISION NR K DTD 08/18/2004 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 FQML-3027 REVISION NR 8 DTD 03/08/2022 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 NDTS-1101 REVISION NR H2 DTD 02/17/1993 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 NDTS-1101 CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 10 OF 29 PAGES SPE4A7-24-T-186L SECTION B REVISION NR H3 DTD 09/29/1995 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 NDTS-1101 REVISION NR K DTD 12/11/2019 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 NDTS-5101-4 REVISION NR 4A DTD 10/02/1986 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 FMS-3002 REVISION NR A2 DTD 10/23/1990 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 16Z001 REVISION NR AK DTD 03/11/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 NDTS-1501 REVISION NR K DTD 08/18/2004 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 NDTS-1501 REVISION NR K1 DTD 11/10/2004 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 NDTS-1500 REVISION NR K1 DTD 01/10/2005 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 16Z001ISS204 REVISION NR FZ DTD 12/21/2011 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 FPS-3017 REVISION NR G DTD 06/23/2020 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 FMS-3027 REVISION NR C DTD 06/26/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 M16L113/1 REVISION NR V DTD 03/26/1981 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 NDTS-5101 REVISION NR A3 DTD 10/31/1986 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 FQML-3002 REVISION NR 14 DTD 04/23/2019 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 16PR070 REVISION NR A DTD 05/21/2003 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 16PR070 REVISION NR B DTD 05/21/2003 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 FMS-3027 REVISION NR C DTD 10/24/1994 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 NDTS-5101-1 REVISION NR 1A DTD 09/05/1975 PART PIECE NUMBER: CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 11 OF 29 PAGES SPE4A7-24-T-186L SECTION B IAW REFERENCE DRAWING NR 81755 NDTS-5101-2 REVISION NR 2A DTD 10/29/1976 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 NDTS-5101-3 REVISION NR 3A DTD 10/29/1976 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 M16L108/1 REVISION NR BA DTD 11/03/1978 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 M16L108/2 REVISION NR AG DTD 01/01/1939 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 M16L108/3 REVISION NR BA DTD 01/01/1939 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 M16L108/4 REVISION NR AG DTD 01/01/1939 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 M16L108/5 REVISION NR AG DTD 01/01/1939 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 M16L108/6 REVISION NR U DTD 01/01/1939 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 M16L108/7 REVISION NR AG DTD 01/01/1939 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 M16L108/8 REVISION NR AG DTD 01/01/1939 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81755 M16L108/9 REVISION NR AG DTD 01/01/1939 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 13873 EI-011201868 REVISION NR DTD 03/26/2024 PART PIECE NUMBER: CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0001 7006804112 0001 EA 2.000 NSN/MATERIAL:1560011201868 DELIVERY (IN DAYS):0397 DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN PREP FOR DELIVERY: