HANDLE, MANUAL CONTR

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 26 PAGES SPE7L1-23-U-1122 SECTION A DESTINATION INSPECTION REQUIRED - FAR 52.246-2 APPLIES. Fast Pay does not apply to this solicitation Offerors are encouraged to submit price break information (not Auto IDC) with their quotes. Solicitations which are manually evaluated and awarded at increased quantities may be awarded based on the price break information submitted with the offeror's original quotation without further solicitation or discussion. This does not apply to Auto IDC. If you anticipate quoting on a solicitation after the closing date, please submit a DIBBS quote with a bid type of “No Bid” and place an anticipated quote date or the reason you are not willing to quote. This does not prevent you from submitting an actual quote on DIBBS at a later date. It will overlay your previous no quote. This informs buyers of your intention to quote and prevents multiple calls for updates and

cancelling of requirements assumed to be non-procurable due to no quotes/sources. The submission of an anticipated quote date does not preclude DLA from making an award to another acceptable timely offer. DLA funds Procurement Technical Assistance Centers (PTACs) to increase the number of U.S. businesses capable of bidding and performing on local, state, and federal government contracts. PTACs have government contracting experts available to assist suppliers at no cost. Visit our website to find your local PTAC: http://www.dla.mil/HQ/SmallBusiness/PTAP.aspx THE OFFEROR, BY SUBMISSION OF ITS QUOTATION, REPRESENTS IT WILL NOT PROVIDE COVERED TELECOMMUNICATIONS EQUIPMENT OR SERVICES TO THE GOVERNMENT IN THE PERFORMANCE OF ANY AWARD RESULTING FROM THIS SOLICITATION, IN ACCORDANCE WITH PARAGRAPH (d)OF THE CLAUSE AT FAR CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 26 PAGES SPE7L1-23-U-1122 SECTION A 52.204-24, REPRESENTATION REGARDING CERTAIN TELECOMMUNICATIONS AND VIDEO SURVEILLANCE SERVICES OR EQUIPMENT, OR IN ACCORDANCE WITH ITS EXISTING REPRESENTATION IN PARAGRAPH (c) OF THE PROVISION AT DFARS 252.204-7016, COVERED DEFENSE TELECOMMUNICATIONS EQUIPMENT OR SERVICES – REPRESENTATION. Caution Notice: Offerors are required to comply with domestic material restrictions. The Berry Amendment, the Buy American Act, and other domestic material restriction may apply. Offerors are instructed to refer to the solicitation clauses related to foreign sourcing for more information on applicability. The Berry Amendment threshold has been reduced to $150,000 and vendors must carefully review related clauses DFARS 252.225-7006, 252.225-7012, and 252.225-7015 for applicability requirements. If your offer is based on a non-domestic material, you are required to provide disclosure information in your quote and/or through written notification to the point of contact listed in the solicitation. DoD Class Deviation 2023-O0001: A small business joint venture offeror must submit, with its offer, the representation required in paragraph (c) of FAR solicitation provision 52.212-3, Offeror Representations and Certifications-Commercial Products and Commercial Services, and paragraph (c) of FAR solicitation provision 52.219-1, Small Business Program Representations, in accordance with 52.204-8(d) and 52.212- 3(b) for the following categories: (A) Small business; (B) Service-disabled veteran-owned small business; (C) Women-owned small business (WOSB) under the WOSB Program; (D) Economically disadvantaged women-owned small business under the WOSB Program; or (E) Historically underutilized business zone small business. Contractors shall not provide parts and supplies made using additive manufacturing (AM), unless AM is specifically authorized in the solicitation/contract. See procurement note L31. CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 26 PAGES SPE7L1-23-U-1122 SECTION A Procurement History for NSN/FSC:010737685/5340 CAGE Contract Number Quantity Unit Cost AWD Date Surplus Material . 4L516 SPE7L123V1544 53.000 113.20000 20221206 N 4L516 SPE5EM18V8016P00001 230.000 95.65000 20180906 N 4L516 SPE5EM17V3180 60.000 99.95000 20170224 N 4L516 SPE5EM16V5666 47.000 105.50000 20160621 N 7W356 SPE5E016M0230 53.000 53.26000 20160209 N 4L516 SPM5E413V2635 47.000 39.50000 20130322 N 4L516 SPM5EK12M3221 45.000 39.75000 20120926 N 4L516 SPM5EK12V1567 34.000 39.75000 20120924 N T8668 SPM5L311M0532 50.000 41.00000 20110119 N 48406 SP056006CF048 150.000 33.80000 20060830 N 32783 SP056003MDZ57 150.000 31.87000 20030914 N 51071 DAAE0787P3830 519.000 12.85000 19870827 N 01417 DAAE0781G00030008 191.000 16.92000 19811210 N 01417 DAAE0781G00030001 117.000 20.55000 19810331 N 01417 DAAE0779C0149 16.000 22.09000 19790221 N This solicitation is being issued under the First Destination Transportation (FDT) program to reduce cost of transportation through the use of Government-Arranged Transportation utilizing Government contracts and rates. Offers should be submitted based on FOB Origin. For offerors whose shipments will orginate from outside the contiguous United States, the offeror's FOB Origin price shall include transportation to a contiguous United States location that the offeror selects based on cost effectiveness or other variables at the offeror's discretion. Additional information about FDT can be found at: http://www.dla.mil/FDTPI/ CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 26 PAGES SPE7L1-23-U-1122 SECTION B PR: 1000161341 NSN/MATERIAL:5340010737685 ITEM DESCRIPTION HANDLE,MANUAL CONTR HANDLE,MANUAL CONTROL RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. Certificate of Quality Compliance (CoQC) Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. If CDRL-COQCCDRLs is missing from DLA Collaboration Folders (CFolders) they can also be viewed in Appendix 1 of the DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. The following Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. RQ006: QUALITY CONFORMANCE INSPECTION REQUIREMENTS CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 26 PAGES SPE7L1-23-U-1122 SECTION B RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES (19207) U S ARMY TANK AUTOMOTIVE COMMAND SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. REFERENCE MATERIAL SOURCE INSPECTION REQUIRED. A metal casting process was identified as a means to manufacture this item. Tooling is required to produce a casting. For sourcing, tooling, materials or other information, please contact the appropriate assistance team: (Aviation, C&E Supply Chains) DSCR.AFCAT@dla.mil; (Land & Maritime Supply Chains) DSCC.cast.forge@dla.mil CRITICAL APPLICATION ITEM IAW BASIC DRAWING NR 19207 12274684 REVISION NR G DTD 09/26/2016 PART PIECE NUMBER: IAW REFERENCE QAP 19207 12274684 REVISION NR E DTD 11/17/1992 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12274684 REVISION NR DTD 08/23/2017 PART PIECE NUMBER: IAW REFERENCE NON GOVT STD QQ-C-320 REVISION NR 04 DTD PART PIECE NUMBER: IAW REFERENCE QAP 13873 CDRL-COQC-22104 REVISION NR DTD 04/08/2022 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 SCR-00004982 REVISION NR DTD 08/09/2016 PART PIECE NUMBER: LINE ITEM 0000000001 TYPE OF COVERAGE: DLA DIRECT, CONUS CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0001 1000161341 0001 EA 108.000 * This is an estimated quantity and may not be purchased by the IDC. NSN/MATERIAL:5340010737685 DELIVERY (IN DAYS):0155 DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 10 OF 26 PAGES SPE7L1-23-U-1122 SECTION B PR: 1000161341 PRLI: 0001 CONT’D INSPECTION POINT: DESTINATION ACCEPTANCE POINT: DESTINATION PREP FOR DELIVERY: PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999 QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00 WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0 UNIT CONT:10 OPI:O INTRMDTE CONT:D3 INTRMDTE CONT QTY:AAA PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:00 -00 No special marking PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT IP025: PACKAGING, MARKING, AND SHIPPING OF HAZARDOUS MATERIALS * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 11 OF 26 PAGES CONTINUED ON NEXT PAGE SPE7L1-23-U-1122