BELT, VEHICULAR SAFETY

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 26 PAGES SPE7L4-23-T-2831 SECTION A GOVERNMENT IN THE PERFORMANCE OF ANY AWARD RESULTING FROM THIS SOLICITATION, IN ACCORDANCE WITH PARAGRAPH (d)OF THE CLAUSE AT FAR 52.204-24, REPRESENTATION REGARDING CERTAIN TELECOMMUNICATIONS AND VIDEO SURVEILLANCE SERVICES OR EQUIPMENT, OR IN ACCORDANCE WITH ITS EXISTING REPRESENTATION IN PARAGRAPH (c) OF THE PROVISION AT DFARS 252.204-7016, COVERED DEFENSE TELECOMMUNICATIONS EQUIPMENT OR SERVICES – REPRESENTATION. Caution Notice: Offerors are required to comply with domestic material restrictions. The Berry Amendment, the Buy American Act, and other domestic material restriction may apply. Offerors are instructed to refer to the solicitation clauses related to foreign sourcing for more information on applicability. The Berry Amendment threshold has been reduced to $150,000 and vendors must carefully review related clauses DFARS 252.225-7006,

252.225-7012, and 252.225-7015 for applicability requirements. If your offer is based on a non-domestic material, you are required to provide disclosure information in your quote and/or through written notification to the point of contact listed in the solicitation. DoD Class Deviation 2023-O0001: A small business joint venture offeror must submit, with its offer, the representation required in paragraph (c) of FAR solicitation provision 52.212-3, Offeror Representations and Certifications-Commercial Products and Commercial Services, and paragraph (c) of FAR solicitation provision 52.219-1, Small Business Program Representations, in accordance with 52.204-8(d) and 52.212- 3(b) for the following categories: (A) Small business; (B) Service-disabled veteran-owned small business; (C) Women-owned small business (WOSB) under the WOSB Program; (D) Economically disadvantaged women-owned small business under the WOSB Program; or (E) Historically underutilized business zone small business. Contractors shall not provide parts and supplies made using additive manufacturing (AM), unless AM is specifically authorized in the CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 26 PAGES SPE7L4-23-T-2831 SECTION A solicitation/contract. See procurement note L31. Procurement History for NSN/FSC:012461013/2540 CAGE Contract Number Quantity Unit Cost AWD Date Surplus Material . 98313 SPE7L322F075Z 79.000 99.00000 20220512 N 98313 SPE7L322F3476 126.000 99.00000 20211119 N 98313 SPE7L322F2298 54.000 99.00000 20211015 N 98313 SPE7L322F1415 74.000 99.00000 20211007 N 1WZZ2 SPE7L321F015NP00001 28.000 84.00000 20210415 N 1WZZ2 SPE7L321F8421 59.000 84.00000 20210211 N 1WZZ2 SPE7L321F6471 15.000 84.00000 20210107 N 1WZZ2 SPE7L321F4973 25.000 84.00000 20201203 N 1WZZ2 SPE7L321F4793 17.000 84.00000 20201124 N 7Z016 SPE7L120V0646 285.000 75.99000 20191118 N 7Z016 SPE7L119V2042 273.000 76.46000 20181219 N 7Z016 SPE7L118V5765 125.000 74.18000 20180601 N 7Z016 SPE7L117V6307 168.000 70.53000 20170626 N 7Z016 SPE7L517V0714 118.000 70.53000 20170306 N 7Z016 SPE7L416V1860 116.000 62.98000 20160728 N 98313 SPE7L215V3292P00001 244.000 48.88000 20150511 N 1WZZ2 SPE7L015V1424 400.000 49.05000 20141105 N 4V314 SPM7LX13D9002136S01 1.000 63.13000 20130806 N 4V314 SPM7LX13D9002699001 33.000 61.52000 20130416 N 4V314 SPM7LX13D9002058001 33.000 61.52000 20130224 N This solicitation is being issued under the First Destination Transportation (FDT) program to reduce cost of transportation through the use of Government-Arranged Transportation utilizing Government contracts and rates. Offers should be submitted based on FOB Origin. For offerors whose shipments will orginate from outside the contiguous United States, the offeror's FOB Origin price shall include transportation to a contiguous United States location that the offeror selects based on cost effectiveness or other variables at the offeror's discretion. Additional information about FDT can be found at: http://www.dla.mil/FDTPI/ CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 26 PAGES SPE7L4-23-T-2831 SECTION B PR: 0095988638 NSN/MATERIAL:2540012461013 ITEM DESCRIPTION BELT,VEHICULAR SAFETY HARNESS, SAFETY, PERSONNEL. USED ON M113. RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. RD002, COVERED DEFENSE INFORMATION APPLIES RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS) CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 26 PAGES SPE7L4-23-T-2831 SECTION B RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING . CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS. . "ANY ITEM PREVIOUSLY TESTED BY A VENDOR IN ACCORDANCE WITH *** QUALIFICATION*** REQUIREMENTS (FOR EXAMPLE: FAT, HIGH SHOCK AND/OR VIBRATION TEST), STATED ON DWG, SPECIFICATION, OR STANDARD MAY NOT REQUIRE FURTHER TESTING BY THE SAME VENDOR EXCEPT FOR A LATER CHANGE IN DESIGN, MANUFACTURING PROCEDURES, OR TESTING REQUIREMENTS. A CERTIFICATION OF CONFORMANCE WITH PREVIOUS TEST RESULTS ATTESTING APPLICABILITY SHALL BE SUBMITTED FOR ITEMS PREVIOUSLY TESTED." . SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. . FULL AND OPEN COMPETITION APPLY CRITICAL APPLICATION ITEM IAW BASIC DRAWING NR 19207 12252978 REVISION NR E DTD 01/01/1999 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12252978 REVISION NR DTD 05/01/2018 PART PIECE NUMBER: IAW REFERENCE QAP 19207 12252978 REVISION NR B DTD 07/28/1992 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12252978 REVISION NR DTD 10/30/2012 PART PIECE NUMBER: CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 26 PAGES SPE7L4-23-T-2831 SECTION B CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0001 0095988638 0001 EA 19.000 NSN/MATERIAL:2540012461013 DELIVERY (IN DAYS):0062 DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN PREP FOR DELIVERY: PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999 QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00 WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0 UNIT CONT:D3 OPI:M INTRMDTE CONT:D3 INTRMDTE CONT QTY:AAA PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:00 -00 No special marking PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT IP025: PACKAGING, MARKING, AND SHIPPING OF HAZARDOUS MATERIALS PARCEL POST ADDRESS: W25G1U W1A8 DLA DISTRIBUTION DDSP NEW CUMBERLAND FACILITY 2001 NORMANDY DRIVE DOOR 113 TO 134 NEW CUMBERLAND PA 17070-5002 US FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND CONTRACT FREIGHT SHIPPING ADDRESS: W25G1U W1A8 DLA DISTRIBUTION DDSP NEW CUMBERLAND FACILITY 2001 NORMANDY DRIVE DOOR 113 TO 134 NEW CUMBERLAND PA 17070-5002 US Need Ship Date:03/15/2023 Original Required Delivery Date:03/17/2023 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 10 OF 26 PAGES SPE7L4-23-T-2831 SECTION B PR: PRLI: CONT’D PRODUCTION LOT TEST APPROVAL - CONTRACTOR TESTING REQUIRED (REFER TO PROCUREMENT NOTE E03 FOR ADDITIONAL INFORMATION) CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0002 0000000000 EA 1.000 NSN/MATERIAL:S00000062 DELIVERY (IN DAYS):0032 THIS LINE ITEM SIGNIFIES THE PRODUCTION LOT TEST REQUIREMENT (PLT). DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN Need Ship Date:00/00/0000 Original Required Delivery Date:00/00/0000 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 11 OF 26 PAGES CONTINUED ON NEXT PAGE SPE7L4-23-T-2831