PLATE, AUTOMOBILE, IN

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 27 PAGES SPE1C1-23-T-0786 SECTION A (D) Economically disadvantaged women-owned small business under the WOSB Program; or (E) Historically underutilized business zone small business. Procurement History for NSN/FSC:002457819/8345 CAGE Contract Number Quantity Unit Cost AWD Date Surplus Material . 1N192 SP010097AS100D599 20.000 45.00000 19970904 N CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 27 PAGES SPE1C1-23-T-0786 SECTION B PR: 7001835370 NSN/MATERIAL:8345002457819 ITEM DESCRIPTION PLATE,AUTOMOBILE,IN "PLATE, AUTOMOBILE, INDIVIDUAL " SECRETARY OF THE ARMY "6 IN W, SECRETARY OF THE ARMY " IAW MIL-DTL-14631/7E . RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY

REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. ADDITIONAL INFORMATION FOR MIL-DTL-14631: . IN ACCORDANCE WITH DETAIL SPECIFICATION MIL-DTL-14631C, 16 DECEMBER 1997, SUPPLEMENT 1A, 3 MAY 2000. . NOTE: THE INSPECTION LEVELS AND ACCEPTABLE QUALITY LEVELS (AQL'S) EXPRESSED IN DEFECTS PER HUNDRED UNITS SHALL BE AS FOLLOWS: FOR EXAMINATIONS APPLICABLE TO 4.5.3.1.1 - INSPECTION LEVEL II, AQL, MAJOR 1.5, TOTAL, 6.5. FOR EXAMINATIONS APPLICABLE TO 4.5.3.1.2 - INSPECTION LEVEL S-1, AQL, ONE CLASS, TOTAL, 2.5 . EACH PLATE SHALL BE PRESERVED AND PACKAGED IN ACCORDANCE WITH THE APPLICABLE REQUIREMENTS OF ASTM-D-3951. IN ADDITION, EACH PLATE SHALL BE COMPLETELY ENCLOSED IN A WRAP OF NOT LESS THAN TWO THICKNESS OF REGULAR, GRADE A, WHITE TISSUE PAPER. EACH TISSUE WRAPPED PLATE SHALL THEN BE PLACED IN A SEALED KRAFT PAPER ENVELOPE OR COMPLETELY OVERWRAPPED WITH 30 POUND MINIMUM BASIS WEIGHT KRAFT PAPER. THE OVERWRAP SHALL BE SECURED WITH ADHESIVE OR 2 INCH (5.08 CM) MINIMUM WIDTH GUMMED PAPER TAPE. AS AN ALTERNATIVE TO THE TISSUE PAPER AND KRAFT PAPER ENVELOPE OR WRAP, EACH PLATE MAY BE PLACED IN A SNUG-FITTED POLYETHYLENE BAG. WHEN USED, THE POLYETHYLENE FILM SHALL BE 0.003 INCH (0.007 CM) THICK. ALL SEAMS AND CLOSURES SHALL BE EFFECTED BY HEAT SEALING. PRIOR TO OR DURING THE HEAT SEALING OPERATION, EXCESS AIR WITHIN THE BAG SHALL BE EXPELLED. PLATES ASSEMBLED WITH STARS SHALL BE ENCLOSED IN A COMMERCIALLY ACCEPTABLE BUBBLE WRAP OR CORRUGATED FIBERBOARD WRAP PRIOR TO AFOREMENTIONED OVERWRAPPING OR SEALING. . BAR CODE LABEL/TAG AND PACKAGING INFORMATION FOR THIS SPECIFICATION IS AN GOVERNMENT LOANED CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 27 PAGES SPE1C1-23-T-0786 SECTION B HUBS. ALSO PACKAGING INFORMATION IS ON AN DEFENSE AGENCY AUTOMATED PACKAGING CD-ROM. ADDITIONAL INFORMATION FOR TT-P-1757B: . NO ADDITIONAL INFORMATION FOLLOWS. . ADDITIONAL INFORMATION FOR PPP-B-636: FEDERAL SPECIFICATION PPP-B-636 DATED JULY 12, 1981, INCLUDING INTERIM FEDERAL SPECIFICATION PPP-B-636L DATED JANUARY 1, 1991, IS HEREBY CANCELLED, AND REPLACED WITH ASTM-D-5118, STANDARD PRACTICE FOR FABRICATION OF FIBERBOARD SHIPPING BOXES, AND ASTM-D-1974, STANDARD PRACTICE FOR METHOD OF CLOSING, SEALING AND REINFORCING FIBERBOARD SHIPPING CONTAINERS. ADDITIONAL INFORMATION FOR MIL-C-5541E: . NO ADDITIONAL INFORMATION FOLLOWS. . ADDITIONAL INFORMATION FOR MIL-P-15011: NO ADDITIONAL INFORMATION FOLLOWS. (ref. T1368 - 6/15/06) FED-STD-595C, COLORS USED IN GOVERNMENT PROCUREMENT, AND ALL ASSOCIATED SLASH SHEETS HAVE BEEN CANCELLED (FEBRUARY 14, 2017) AND SUPERSEDED BY SAE AMS-STD-595. ADDITIONAL INFORMATION FOR SAE AMS-STD-595: COPIES OF SAE AMS-STD-595 CAN BE OBTAINED FROM: WEBSITE: STORE.SAE.ORG/EA/ TELEPHONE: 877-606-7323 (INSIDE USA AND CANADA) +1 724-776-4970 (OUTSIDE USA) MAIL: SAE CUSTOMER SERVICE 400 COMMONWEALTH DRIVE WARRENDALE, PA 15096-0001 INSPECTION OF SUPPLIES SHALL BE IN ACCORDANCE WITH FAR PART 52.246-2 STANDARD INSPECTION. ADDITIONAL INFORMATION FOR MIL-STD-105E: MIL-STD-105E, dated 10 May 1989, is hereby canceled. Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product," or ANSI/ASQ Z1.4, "Sampling Procedures and Tables for Inspection by Attributes." Users are cautioned to evaluate these documents for their particular application before citing it as a replacement document. (Copies of MIL-STD-1916 are available online at http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) (Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207-6028.) MIL-STD-129R w/CHANGE 2 - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY MARKING FOR SHIPMENT AND STORAGE DATED: 27 SEPTEMBER 2019 INTERIM CHANGES: OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C(>&)>T) DIRECTORATE: THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 27 PAGES SPE1C1-23-T-0786 SECTION B MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C(>&)>T ITEMS, REGARDLESS OF MODE OF SHIPMENT. IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C(>&)>T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER. MIL-STD-147E w/CHANGE 2 27 JUNE 2019 DEPARTMENT OF DEFENSE STANDARD PRACTICE PALLETIZED UNIT LOADS ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4: NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED. APPLICATION FOR COPIES SHOULD BE ADDRESSED TO: AMERICAN SOCIETY FOR QUALITY 600 NORTH PLANKINTON AVENUE MILWAUKEE, WISCONSIN 53203 (Ref. T0795 - May 17, 2006) Two (2) First Article samples are required. First Article Testing shall be performed and the contractor will be notified in writing within thirty (30) calendar days after Contracting Officer's receipt of First Article samples. IT IS RECOMMENDED THAT TWO EACH FIRST ARTICLE SAMPLES OF THE END ITEM(S) BE SUBMITTED TO THIS CENTER FOR VISUAL, DIMENSIONAL AND SHADE EXAMINATIONS. THIRTY DAYS WILL BE REQUIRED TO EXAMINE AND EVALUATE THE SAMPLES AND TO FURNISH THE RESULTS AND DIRECTIONS REGARDING PRODUCTION TO THE CONTRACTOR. IAW BASIC SPEC NR MIL-DTL-14631C SUP 1C NOT 3 REVISION NR C DTD 01/27/2022 PART PIECE NUMBER: IAW REFERENCE SPEC NR MIL-DTL-5541F NOT 1 REVISION NR F DTD 04/09/2019 PART PIECE NUMBER: IAW REFERENCE SPEC NR MIL-DTL-15011K(1) NOT 1 REVISION NR 1 DTD 02/24/2023 PART PIECE NUMBER: IAW REFERENCE STD NR MIL-STD-105E NOT 3 REVISION NR E DTD 02/06/2008 PART PIECE NUMBER: IAW REFERENCE STD NR MIL-STD-129R(2) REVISION NR R DTD 09/27/2019 PART PIECE NUMBER: IAW REFERENCE STD NR MIL-STD-147E(2) REVISION NR E DTD 06/27/2019 PART PIECE NUMBER: IAW REFERENCE STD NR MIL-STD-1249A NOT 1 REVISION NR A DTD 04/08/1996 PART PIECE NUMBER: IAW REFERENCE STD NR MIL-STD-1916 NOT 2 REVISION NR DTD 06/05/2014 PART PIECE NUMBER: IAW REFERENCE CID A-A-203C NOT 3 REVISION NR C DTD 11/19/2004 PART PIECE NUMBER: CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 27 PAGES SPE1C1-23-T-0786 SECTION B IAW REFERENCE CID A-A-1249A NOT 3 REVISION NR A DTD 09/22/2020 PART PIECE NUMBER: IAW REFERENCE CID A-A-1492B NOT 1 REVISION NR B DTD 11/03/1999 PART PIECE NUMBER: IAW REFERENCE CID A-A-1671B(I1) NOT 2 REVISION NR 1 DTD 02/15/2000 PART PIECE NUMBER: IAW REFERENCE CID A-A-1894B NOT 1 REVISION NR B DTD 10/20/1999 PART PIECE NUMBER: IAW REFERENCE UNK TT-L-50G(I3) NOT 1 REVISION NR 3 DTD 03/30/1999 PART PIECE NUMBER: IAW REFERENCE UNK TT-E-489J NOT 2 REVISION NR J DTD 07/30/2008 PART PIECE NUMBER: IAW REFERENCE UNK TT-P-1757B REVISION NR B DTD 05/15/1997 PART PIECE NUMBER: IAW REFERENCE UNK UU-P-268G(3) NOT 1 REVISION NR 3 DTD 07/13/1995 PART PIECE NUMBER: IAW REFERENCE UNK PPP-T-45D NOT 2 REVISION NR D DTD 06/28/1993 PART PIECE NUMBER: IAW REFERENCE UNK PPP-B-621D(3) NOT 2 REVISION NR 3 DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE UNK PPP-B-636J(4) NOT 1 REVISION NR 4 DTD 03/01/1994 PART PIECE NUMBER: IAW REFERENCE UNK FED-STD-595C(1) REVISION NR C DTD 07/31/2008 PART PIECE NUMBER: IAW REFERENCE NON GOVT STD ASQ Z1.4 (R 2018) REVISION NR DTD 01/01/2003 PART PIECE NUMBER: IAW REFERENCE NON GOVT STD ASTM D5118/D5118M REVISION NR DTD 11/01/2022 PART PIECE NUMBER: IAW REFERENCE NON GOVT STD ASTM D6251 REVISION NR DTD PART PIECE NUMBER: IAW REFERENCE NON GOVT STD ASTM D1974/D1974M REVISION NR DTD 05/01/2022 PART PIECE NUMBER: IAW REFERENCE NON GOVT STD ASTM D6880 REVISION NR DTD 04/01/2011 PART PIECE NUMBER: CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 10 OF 27 PAGES SPE1C1-23-T-0786 SECTION B CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0001 7001835370 0001 EA 30.000 NSN/MATERIAL:8345002457819 DELIVERY (IN DAYS):0126 DELIVER FOB: DESTINATION QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: DESTINATION ACCEPTANCE POINT: DESTINATION PREP FOR DELIVERY: PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999 QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:ZZ WRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNN THKNESS:C UNIT CONT:ZZ OPI:O INTRMDTE CONT:ZZ INTRMDTE CONT QTY:XXX PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:00 -00 No special marking PRES/PACK LEVELS SHALL BE A/C IN ACCORDANCE WITH MIL-P-14631. SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE SUPPLIES". NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING MATERIALS: "All Wood Packaging Material (WPM) acquired by DOD must meet requirements of International Standards for Phytosanitary Measures (ISPM) 15, "Guidelines for Regulating Wood Packaging Materials in International Trade." DOD shipments inside and outside of the United States must meet ISPM 15 whenever WPM is used to ship DOD cargo, or when wood is being acquired by DLA for future use as packaging material. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board (OSD). All WPM shall comply with one of the following official quality control programs: Heat Treatment (HT) or Kiln Dried Heat Treatment (KD HT) in accordance with American Lumber Standard Committee, Incorporated (ALSC) Wood Packaging Material Program and WPM Enforcement Regulations (see http://www.alsc.org/; or All WPM shall include certification/quality markings in accordance with the ALSC or NWPCA standards, as applicable. Markings shall be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides of the pallet and be contrasting and clearly visible. All containers shall be marked on a side other than the top or bottom, contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ASLC approved DUNNAGE stamp. Failure to comply with the requirements of this restriction may result in refusal, destruction, or treatment of materials at the point of entry. The Agency reserves the right to recoup from the Contractor any remediation costs incurred by the Government." CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 11 OF 27 PAGES SPE1C1-23-T-0786 SECTION B PR: 7001835370 PRLI: 0001 CONT’D PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD DIMENSIONS SHALL NOT EXCEED 43 INCHES IN LENGTH, 52 INCHES IN WIDTH, AND 54 INCHES IN HEIGHT (INCLUDING THE PALLET). THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL BONDING MATERIALS. THE USE OF METAL BANDING, IN SECURING BOXES TO PALLETS, IS DISCOURAGED. PALLET LOADS SHALL CONTAIN THE SAME NUMBER OF CARTONS, OF IDENTICAL QUANTITIES, OF ONE NSN, TO THE MAXIMUM EXTENT POSSIBLE. PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE THAN ONE NSN. AT THE END OF A SIZE RUN, NO MORE THAN ONE CARTON PER NSN MAY BE SHORT OR OVER THE SPECIFIED QUANTITY. SAID CARTON SHALL BE CLEARLY MARKED "SHORT" OR "OVER". MIL-STD-147 IS REFERENCED FOR PALLETIZED LOADS. IN ADDITION TO REQUIREMENTS SPECIFIED ABOVE THE FOLLOWING CLAUSE ALSO APPLIES: 52.247-9012 - REQUIREMENTS FOR TREATEMENT OF WOOD PACKAGING MATERIALS (WPM) - (JULY 2006) PARCEL POST ADDRESS: UY8615 ARIZONA INDUSTRIES FOR THE BLIND 515 N 51ST AVENUE NUMBER 130 DOCK 1 PHOENIX AZ 85043 US FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND CONTRACT FREIGHT SHIPPING ADDRESS: UY8615 ARIZONA INDUSTRIES FOR THE BLIND 515 N 51ST AVENUE NUMBER 130 DOCK 1 PHOENIX AZ 85043 US Need Ship Date:00/00/0000 Original Required Delivery Date:03/28/2023 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *