SUPPORT, SEAT FRAME,

expired opportunity(Expired)
From: Federal Government(Federal)
started - 13 Aug, 2022 (1 month ago)

Start Date

13 Aug, 2022 (1 month ago)
due - 13 Aug, 2022 (1 month ago)

Due Date

23 Aug, 2022 (1 month ago)
Bid Notification

Opportunity Type

Bid Notification
SPE4A7-22-Q-1443

Opportunity Identifier

SPE4A7-22-Q-1443
Department of Defense

Customer / Agency

Department of Defense
700 Robbins Avenue Philadelphia PA 19111

Location

700 Robbins Avenue Philadelphia PA 19111
unlockUnlock the best of InstantMarkets.
Please Sign In to see more out of InstantMarkets such as history, intelligent business alerts and many more.

Don't have an account yet? Create a free account now.

SUPPLY/SERVICE: 1680-01-617-8365 CONT'D customer. DFARS 252.211-7003(c)(1)(i) applies. RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER) RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. MIL-STD-130N(1) DATED 16 NOV 2012. IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY Government First Article Preproduction approval required. Testing will be in accordance with applicable drawings, specifications and/or Engineering instructions. The first article offered shall be manufactured at the facilities in which production quantities are procured and produced under this contract. When submitting the first article(s) for government testing, a copy of the contract and all applicable drawings, specifications, engineering instructions, certifications, and inspection sheets shall be provided. Upon receipt and evaluation of the test report from the responsible government testing location, the contracting officer will provide final notification to the manufacturer. Any questions or concerns regarding the first article test requirements must be submitted through the contracting officer. Additional Wide Area Workflow (WAWF) instructions for government first article test CLIN: The contractor shall code the receiving report for government first article test CLIN in WAWF as Follows: A: Inspection at origin (Source) - Enter the DCMA office DODAAC listed on page 1 of the contract. B: Acceptance by other - Enter the issue by office DODAAC listed on page 1 of the contract. C: Ship to code - Enter the DODAAC of the test facility listed for the government first article test CLIN in the contract (See FAR Clause 52.209-4). FIRST ARTICLE TEST MARKING INSTRUCTIONS: FAT sample(s) packaging shall be clearly marked "FIRST ARTICLE TEST EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contrasting color to the packaging. Marking shall be located adjacent to the Package Shipping Label side and on at least one additional side of CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 36 PAGES SPE4A7-22-Q-1443 SECTION B SUPPLY/SERVICE: 1680-01-617-8365 CONT'D the package. remarks: DWG: 201112671(>,)> 201112695; -10 DWG: 201112694;-01,-03 DWG: 201112656:-03 DWG: 201112736; -01,-03,-05 // Vendor Item Control Drawing DWG: 201112699; -01 - Pin,Rotational Lock, -03 - Base, Handle, -05 - Lever, Handle, -07 - Cover(>,)> Handle, -11 - Lifter, Handle DWG: 201112741(>,)> 201112702, 201112701, 201112700(>,)> 201112698 (>,)> 201112697(>,)> 201112696,;01 For General Engineering Document Notes, see document number 200415485. Notes are 1,3,4 and 12 apply. Spares Configuration: Per blueprint. IAW BASIC DRAWING NR 98752 201112671 REVISION NR C DTD 03/29/2017 PART PIECE NUMBER: 201112671-10 IAW REFERENCE DRAWING NR 98752 200415485 REVISION NR E DTD 01/30/2020 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98752 201112694 REVISION NR B DTD 06/30/2014 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98752 201112695 REVISION NR DTD 11/16/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98752 201112696 REVISION NR DTD 11/16/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98752 201112697 REVISION NR A DTD 03/13/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98752 201112698 REVISION NR DTD 11/16/2012 PART P

Dates

Start Date

13 Aug, 2022 (1 month ago)

Due Date

23 Aug, 2022 (1 month ago)

You may also like

16--SUPPORT,SEAT FRAME,

Due: 11 Oct, 2022 (in 9 days)Agency: DEPT OF DEFENSE

FRAME, SEAT, VEHICULA

Due: 07 Oct, 2022 (in 5 days)Agency: Department of Defense

HEADREST, SEAT, VEHIC

Due: 03 Oct, 2022 (in 1 day)Agency: Department of Defense
Please Sign In to see more like these.

Don't have an account yet? Create a free account now.

Location

Country : United StatesState : Pennsylvania