FIRST ARTICLE TEST

SUPPLY/SERVICE: 5315-01-537-4652 CONT'D the facilities in which production quantities are procured under the contract. Contractor shall provide a statement along with objective evidence that test and production items meet the material and process requirements of the contract. If applicable, DD form 1423 documentation shall be provided as required. Unless F.A.T sample(s) is degraded or destroyed in testing or submitted for government fit, form, function verification (when specified by contract), the F.A.T. samples(s) may be deliverable with the last production run of the contract. Additional Wide Area Workkflow (WAWF) instructions for contractor first article test CLIN: The contractor shall code the receiving report for contractor first article test CLIN in WAWF as follows: A. Inspection at origin (source)- Enter the DCMA DODAAC listed on page 1 of the contract. B. Acceptance at destination- Enter the issue by office DODAAC listed C. Ship to code - Enter the issue by office DODAAC

listed on page 1 of the contract. The following Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. DEPARTMENT OF ARMY SERIALIZATION REQUIREMENTS: SERIAL NUMBER REPORTING REQUIREMENT (SNRR) & THE ARMY MAINTENANCE MANAGEMENT SYSTEM-AVIATION (TAMMS-A) BOTH DD FORM 1423 REQUIREMENTS APPLY CONTRACT FIRST ARTICLE TEST REQUIREMENTS: IN ADDITION TO THE ABOVE: THE CONTRACTOR SHALL PROVIDE ALL NON- GOVERNMENTAL DRAWINGS, SPECIFICATIONS, AND STANDARDS FOR GOVERNMENT REVIEW OF THE CONTRACTOR'S FIRST ARTICLE TEST REPORT. THIS INFORMATION IS FOR GOVERNMENT USE ONLY AND WILL NOT BE RELEASED. THIS INFORMATION WILL BE RETURNED TO THE CONTRACTOR OR DESTROYED AT THE CONTRACTOR'S DIRECTION. EXCEPTION DATA: CONTRACTOR PRODCUTION LOT TESTING (PLT) IN LIEU OF CONTRACTOR FIRST ARTICLE TESTING (FAT) [ARMY (AMRDEC) APPROVED JUNE 06, 2014] CONTRACTOR PRODUCTION LOT TESTING REQUIREMENTS: THE PRODUCTION LOT SAMPLE QUANTITY SHALL BE IN ACCORDANCE WITH ANSI/ASQ Z1.4-2003 (R2013), SELECTED AT RANDOM BY THE COGNIZANT GOVERNMENT REPRESENTATIVE. SAMPLES SHALL BE IDENTIFIED BY CONTRACT NUMBER AND LOT NUMBER, AND BE CLEARLY MARKED: PRODUCTION LOT SAMPLE. TESTING WILL BE IN ACCORDANCE WITH THE APPLICABLE DWGS/SPECS AND CONTRACT REQUIREMENTS. IN ORDER FOR A PRODUCTION LOT TO BE ACCEPTABLE, ALL SAMPLES REPRESENTATIVE OF THE LOT MUST PASS ALL OF THE CONTRACT REQUIREMENTS. UPON NOTIFICATION OF ACCEPTANCE, SAMPLES WILL BE CONSIDERED PART OF THE PRODUCTION QUANTITY AND SHIPPED WITH THE REST OF THE PRODUCTION LOT. IN THE EVENT A SAMPLE FAILS TO PASS SUCH REQUIREMENTS, THE LOT WILL BE REJECTED. THE PCO WILL BE NOTIFIED 30 DAYS PRIOR TO THE CONTRACTORS DESIRED TEST DATE. A DCMA QAR OR DESIGNATED GOVERNMENT OFFICIAL WILL TRAVEL TO THE MANUFACTURER'S FACILITY TO WITNESS THE CONTRACTOR PERFORM THE PRODUCTION LOT TESTING. A MEMO OF INSPECTION RESULTS IS REQUIRED FROM THE GOVERNMENT REPRESENTATIVE WITNESSING THE TEST FOR EACH LOT INSPECTION. THE CONTRACTING OFFICER AT DSCR WILL PROVIDE FINAL RESULT NOTIFICATION TO THE MANUFACTURER. QUESTIONS REGARDING THE PRODUCTION LOT TEST SHOULD BE SUBMITTED THROUGH THE CONTRACT POST AWARD ADMINISTRATING OFFICER. CRITICAL APPLICATION ITEM CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 4 OF 24 PAGES SPE4A5-24-Q-0538 SECTION B SUPPLY/SERVICE: 5315-01-537-4652 CONT'D SIKORSKY AIRCRAFT CORPORATION 78286 P/N 70103-08108-041 IAW REFERENCE QAP 13873 SQAP-SER1 REVISION NR DTD 12/10/2003 PART PIECE NUMBER: IAW REFERENCE QAP 81996 QE-STD-1 REVISION NR E DTD 06/19/2017 PART PIECE NUMBER: IAW REFERENCE QAP 13873 CDRL-GEN-TAMMSA-19312 REVISION NR DTD 12/08/2019 PART PIECE NUMBER: IAW REFERENCE QAP 13873 CDRL-GEN-SNRR-19312 REVISION NR DTD 12/08/2019 PART PIECE NUMBER: IAW REFERENCE QAP 1X4F3 CDRL-CFAT-SPC05 REVISION NR DTD 10/15/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 78286 70103-08108-041 REVISION NR DTD 01/26/2024 PAR