BULKHEAD, AIRCRAFT

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 25 PAGES SPE4A7-24-T-278Q SECTION A Procurement History for NSN/FSC:015498802/1560 CAGE Contract Number Quantity Unit Cost AWD Date Surplus Material . 3CTQ9 SPM4A708MB820P00001 50.000 142.10000 20080609 N This solicitation is being issued under the First Destination Transportation (FDT) program to reduce cost of transportation through the use of Government-Arranged Transportation utilizing Government contracts and rates. Offers should be submitted based on FOB Origin. For offerors whose shipments will orginate from outside the contiguous United States, the offeror's FOB Origin price shall include transportation to a contiguous United States location that the offeror selects based on cost effectiveness or other variables at the offeror's discretion. Additional information about FDT can be found at:

target="_blank">http://www.dla.mil/FDTPI/ CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 25 PAGES SPE4A7-24-T-278Q SECTION B PR: 7006516962 NSN/MATERIAL:1560015498802 ITEM DESCRIPTION BULKHEAD,AIRCRAFT ITEM:,,BULKHEAD(>,)> AIRCRAFT P/N:,,4-3492-76 RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR) RD002, COVERED DEFENSE INFORMATION APPLIES RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER) RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies. RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ To be eligible for award, offerors and any sources of supply proposed CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 25 PAGES SPE4A7-24-T-278Q SECTION B for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. RQ042: Non-Tailored Higher-Level Quality Requirements (ISO 9001:2015) for Manufacturers and Non-Manufacturers MIL-STD-130N(1) DATED 16 NOV 2012. IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY DIGITAL MYLAR DATA EXISTS FOR THIS NSN, AND WILL BE INCLUDED IN THE TECHNICAL DATA PACKAGE PROVIDED BY DLA. IF UNABLE TO USE THE DATA IN THE DIGITAL FORMAT PROVIDED, THE CONTRACTOR WILL BE RESPONSIBLE FOR HAVING THE DATA CONVERTED TO THE NECESSARY FORMAT (I.E. MYLAR FILM), THROUGH A THIRD PARTY AND BEAR THE ASSOCIATED COSTS WHEN CONVERTING FROM DIGITAL TO STABLE BASED FORMAT, THE DIGITAL MYLAR SHALL BE PLOTTED ON STABLE BASE MATERIAL, WHILE MAINTAINING THE DIMENSIONAL ACCURACY DEMANDS OF THE UNDIMENSIONED DRAWING. THIS INCLUDES BUT IS NOT LIMITED TO: VERIFY THE PLOT OF THE MYLAR(S) FOR DIMENSIONAL ACCURACY AS OUTLINED IN ASME Y14.31. ACCURACY SHALL BE DETERMINED VERTICALLY, HORIZONTALLY AND DIAGONALLY. ENSURE THAT THE INDIVIDUAL GRID UNITS ARE WITHIN THE TOLERANCE OF (+,-) 0.005 INCHES AND (+,-) 0.007 INCHES DIAGONALLY. TOTAL GRID TOLERANCE SHALL BE (+,-) 0.010 INCHES AND (+,-) 0.014 INCHES DIAGONALLY. DRAWINGS WITH DIMENSIONAL ACCURACY POINTS SUCH AS TRAMMEL POINTS SHALL BE MEASURED TO WITHIN CENTERLINE (+,-) 0.010 INCHES AND (+,-) 0.014 INCHES DIAGONALLY. REGISTRATION MARKS SUCH AS THOSE USED ON CIRCUIT CARDS SHALL BE MEASURED TO WITHIN (+,-) 0.005 INCHES AND (+,-) 0.007 INCHES DIAGONALLY. ALL SPECIAL PROCESSES SHALL BE PERFORMED BY ORGANIZATIONS MAINTAINING NADCAP APPROVAL FOR RELEVANT SPECIAL PROCESS. (SEE DRAWING 20145214) DIGITAL MYLAR DATA EXISTS FOR THIS NSN, AND WILL BE INCLUDED IN THE TECHNICAL DATA PACKAGE PROVIDED BY DLA. IF UNABLE TO USE THE DATA IN THE DIGITAL FORMAT PROVIDED, THE CONTRACTOR WILL BE RESPONSIBLE FOR HAVING THE DATA CONVERTED TO THE NECESSARY FORMAT (I.E. MYLAR FILM), THROUGH A THIRD PARTY AND BEAR THE ASSOCIATED COSTS WHEN CONVERTING FROM DIGITAL TO STABLE BASED FORMAT, THE DIGITAL MYLAR SHALL BE PLOTTED ON STABLE BASE MATERIAL, WHILE MAINTAINING THE DIMENSIONAL ACCURACY DEMANDS OF THE UNDIMENSIONED DRAWING. THIS INCLUDES BUT IS NOT LIMITED TO: VERIFY THE PLOT OF THE MYLAR(S) FOR DIMENSIONAL ACCURACY AS OUTLINED IN ASME Y14.31. ACCURACY SHALL BE DETERMINED VERTICALLY, HORIZONTALLY AND DIAGONALLY. ENSURE THAT THE INDIVIDUAL GRID UNITS ARE WITHIN THE TOLERANCE OF (+,-) 0.005 INCHES AND (+,-) 0.007 INCHES DIAGONALLY. TOTAL GRID TOLERANCE SHALL BE (+,-) 0.010 INCHES AND (+,-) 0.014 INCHES DIAGONALLY. DRAWINGS WITH DIMENSIONAL ACCURACY POINTS SUCH AS TRAMMEL POINTS SHALL BE MEASURED TO WITHIN CENTERLINE (+,-) 0.010 INCHES AND (+,-) 0.014 INCHES DIAGONALLY. REGISTRATION MARKS SUCH AS THOSE USED ON CIRCUIT CARDS SHALL BE MEASURED TO WITHIN (+,-) 0.005 INCHES AND (+,-) 0.007 INCHES DIAGONALLY. SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. NORDAM GROUP LLC, THE 29957 P/N 4-3492-76 H & R PARTS CO INC 32821 P/N 4-3492-76 CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 25 PAGES SPE4A7-24-T-278Q SECTION B AERO COMPONENTS, LLC 59213 P/N 4-3492-76 THE BOEING COMPANY 81205 P/N 4-3492-76 INFINITY FABRICATION, INC. 06DM5 P/N 4-3492-76 D-J ENGINEERING INC 0C7H8 P/N 4-3492-76 CAMNETICS MANUFACTURING CORPORATION 0P657 P/N 4-3492-76 VOLUMATIC INC 1P642 P/N 4-3492-76 FMW, INC. 1QJK4 P/N 4-3492-76 MALONES CNC MACHINING INC 2V045 P/N 4-3492-76 IAW REFERENCE DRAWING NR 81205 BAC5300 REVISION NR N DTD 12/05/2016 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 BAC5300-1 REVISION NR H DTD 06/23/2014 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 BAC5300-2 REVISION NR H DTD 09/15/2014 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 4-3492 REVISION NR K DTD 06/29/2009 PART PIECE NUMBER: 4-3492-76 IAW REFERENCE DRAWING NR 81205 4-3492/9 REVISION NR E DTD 11/16/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 4-3492 REVISION NR J DTD 01/13/2005 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 4-3492/6 REVISION NR B DTD 01/01/1939 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 BAC5307 REVISION NR U DTD 11/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 BAC5300-1 REVISION NR H DTD 09/01/2006 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 BAC5300-2 REVISION NR H DTD 09/01/2006 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 13873 EI-015498802 REVISION NR DTD 12/13/2023 PART PIECE NUMBER: CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0001 7006516962 0001 EA 14.000 NSN/MATERIAL:1560015498802 DELIVERY (IN DAYS):0109 DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 25 PAGES SPE4A7-24-T-278Q SECTION B PR: 7006516962 PRLI: 0001 CONT’D ACCEPTANCE POINT: ORIGIN PREP FOR DELIVERY: PKGING DATA-QUP:001 IF MATERIAL IS CONSIDERED HAZARDOUS IAW FED-STD-313, PACKAGE IN ACCORDANCE WITH TQ REQUIREMENT IP025. IF THE MATERIAL IS NOT CONSIDERED HAZARDOUS, IN ACCORDANCE WITH FED-STD-313, THE MATERIAL SHALL BE COMMERCIALLY PACKAGED IN ACCORDANCE WITH ASTM D3951. All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT PARCEL POST ADDRESS: SW3211 DLA DISTRIBUTION DEPOT OKLAHOMA 3301 F AVE CEN REC BLDG 506 DR 22 TINKER AFB OK 73145-8000 US FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND CONTRACT FREIGHT SHIPPING ADDRESS: SW3211 DLA DISTRIBUTION DEPOT OKLAHOMA 3301 F AVE CEN REC BLDG 506 DR 22 TINKER AFB OK 73145-8000 US Need Ship Date:08/19/2024 Original Required Delivery Date:12/17/2024 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 10 OF 25 PAGES CONTINUED ON NEXT PAGE SPE4A7-24-T-278Q