CONTRACTOR FIRST ARTIC

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 26 PAGES SPE7L3-24-T-201V SECTION A https://www.apexaccelerators.us/#/ for more information. 6, THE OFFEROR, BY SUBMISSION OF ITS QUOTATION, REPRESENTS IT WILL NOT PROVIDE COVERED TELECOMMUNICATIONS EQUIPMENT OR SERVICES TO THE GOVERNMENT IN THE PERFORMANCE OF ANY AWARD RESULTING FROM THIS SOLICITATION, IN ACCORDANCE WITH PARAGRAPH (d) OF THE CLAUSE AT FAR 52.204-24, REPRESENTATION REGARDING CERTAIN TELECOMMUNICATIONS AND VIDEO SURVEILLANCE SERVICES OR EQUIPMENT, OR IN ACCORDANCE WITH ITS EXISTING REPRESENTATION IN PARAGRAPH (c) OF THE PROVISION AT DFARS 252.204-7016, COVERED DEFENSE TELECOMMUNICATIONS EQUIPMENT OR SERVICES – REPRESENTATION. Caution Notice: Offerors are required to comply with domestic material restrictions. The Berry Amendment, the Buy American Act, and other domestic material restrictions may

apply. Offerors are instructed to refer to the solicitation clauses related to foreign sourcing for more information on applicability. The Berry Amendment threshold has been reduced to $150,000 and vendors must carefully review related clauses DFARS 252.225-7006, 252.225-7012, and 252.225-7015 for applicability requirements. If your offer is based on a non-domestic material, you are required to provide disclosure information in your quote and/or through written notification to the point of contact listed in the solicitation. DoD Class Deviation 2023-O0001: A small business joint venture offeror must submit, with its offer, the representation required in paragraph (c) of FAR solicitation provision 52.212-3, Offeror Representations and Certifications-Commercial Products and Commercial Services, and paragraph (c) of FAR solicitation provision 52.219-1, Small Business Program Representations, in accordance with 52.204-8(d) and 52.212- 3(b) for the following categories: (A) Small business; (B) Service-disabled veteran-owned small business; (C) Women-owned small business (WOSB) under the WOSB Program; (D) Economically disadvantaged women-owned small business under the WOSB Program; or CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 26 PAGES SPE7L3-24-T-201V SECTION A (E) Historically underutilized business zone small business. Contractors shall not provide parts and supplies made using additive manufacturing (AM), unless AM is specifically authorized in the solicitation/contract. See procurement note L31. Procurement History for NSN/FSC:007689788/3040 CAGE Contract Number Quantity Unit Cost AWD Date Surplus Material . 8UNV3 SPE7L323P0387 116.000 24.90000 20221014 N 05AL4 SPE7L318P7904 188.000 22.00000 20180626 N 7FWE9 SPE7L017P1667 180.000 24.00000 20170515 N 05AL4 SPE7L315M1369 258.000 19.00000 20141119 N 05AL4 SPM7M313M0950 101.000 22.00000 20121106 N 6EH98 SPM7MB11M1830 186.000 19.39000 20110930 N 57LP7 SPM7MB10M0554 88.000 21.10000 20100223 N 05AL4 SPM7A308M1354 172.000 28.40000 20080402 N 05AL4 SPM7A308V0106 130.000 22.80000 20071023 N 05AL4 SPM7A307V1190 112.000 24.20000 20070724 N 2V045 SPM7A307M1052 42.000 28.50000 20070214 N 2V045 SPM7A307M0842 74.000 32.00000 20070129 N 2V045 SP074004M1493 79.000 28.50000 20040928 N 0JYK5 SP074004VA372 31.000 41.25000 20040423 N 66200 SP074004V6356 25.000 47.62000 20040202 N 1VTS0 SP074002MLL46 29.000 42.00000 20020719 N 98897 F0960398G0001UBG4 10.000 266.03000 20010718 N 98897 F0960382G1386SD2300 59.000 103.53000 19830919 N This solicitation is being issued under the First Destination Transportation (FDT) program to reduce cost of transportation through the use of Government-Arranged Transportation utilizing Government contracts and rates. Offers should be submitted based on FOB Origin. For offerors whose shipments will orginate from outside the contiguous United States, the offeror's FOB Origin price shall include transportation to a contiguous United States location that the offeror selects based on cost effectiveness or other variables at the offeror's discretion. Additional information about FDT can be found at: http://www.dla.mil/FDTPI/ CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 26 PAGES SPE7L3-24-T-201V SECTION B PR: 7007086620 NSN/MATERIAL:3040007689788 ITEM DESCRIPTION CAM,CONTROL CAM,CONTROL ENGINEERING NOTES: 1. PART MARKING PER MIL-STD-130, METHOD PER LAC 0227. 2. USE SAE AMS-QQ-A-250/12 ALUMINUM ALLOY 7075 PLATE/SHEET IN LIEU OF QQ-A-283. 3. DIMENSIONS AND TOLERANCES PER ASME Y14.5. 4. DELETE REFERENCE TO DWG NO. 363174. 5. DELETE REFERENCE TO FLAGNOTE 3, PART TO BE FINISHED USING CHROMIC ACID ANODIZING PER MIL-A-8625, TYPE I, CLASS 1. 6. USE STP51-400 IN LIEU OF LAC PROCESS SPEC 701. RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RD002, COVERED DEFENSE INFORMATION APPLIES CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS. RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS) RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER) RQ032: EXPORT CONTROL OF TECHNICAL DATA CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 26 PAGES SPE7L3-24-T-201V SECTION B This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. THIS MATERIAL DOES NOT HAVE A SHELF LIFE REQUIREMENT CRITICAL APPLICATION ITEM IAW BASIC DRAWING NR 98897 357007 REVISION NR C DTD 11/22/1971 PART PIECE NUMBER: 357007-3 IAW REFERENCE DRAWING NR 98897 355111 REVISION NR DTD 11/15/1995 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 363174 REVISION NR B DTD 11/12/1963 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 STP63-001 REVISION NR W DTD 04/28/2023 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 355000 REVISION NR A DTD 02/14/1958 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 STP51-400 REVISION NR E DTD 09/15/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 STP58-209 REVISION NR L DTD 07/22/1988 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98897 LAC701 REVISION NR DTD 10/15/1953 PART PIECE NUMBER: CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 26 PAGES SPE7L3-24-T-201V SECTION B IAW REFERENCE DRAWING NR 98897 G-14 REVISION NR G3 DTD 11/09/2007 PART PIECE NUMBER: IAW REFERENCE QAP 16236 SQAP007689788 REVISION NR DTD 10/12/2023 PART PIECE NUMBER: CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0001 7007086620 0001 EA 192.000 NSN/MATERIAL:3040007689788 DELIVERY (IN DAYS):0299 DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN PREP FOR DELIVERY: PKGING DATA-QUP:001 WILL BE PACKAGED IN ACCORDANCE WITH ASTM D3951. All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT PARCEL POST ADDRESS: SW3119 DLA DISTRIBUTION WARNER ROBINS 455 BYRON STREET BLDG 376 ROBINS A F B GA 31098-1887 US FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND CONTRACT FREIGHT SHIPPING ADDRESS: SW3119 DLA DISTRIBUTION WARNER ROBINS 455 BYRON STREET BLDG 376 ROBINS A F B GA 31098-1887 US Need Ship Date:10/01/2024 Original Required Delivery Date:01/13/2025 CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 10 OF 26 PAGES SPE7L3-24-T-201V SECTION B PR: 7007086620 PRLI: 0001 CONT’D * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * CONTRACTOR FIRST ARTICLE TEST - THE NUMBER OF UNITS SHOWN SIGNIFIES THE TEST REQUIREMENT. SEE FAR CLAUSE 52.209-3 CITED IN SECTION A OF THIS SOLICITATION FOR THE ACTUAL QUANTITY REQUIRED. CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0002 0000000000 EA 1.000 NSN/MATERIAL:0001S00000053 DELIVERY (IN DAYS):0045 THIS LINE ITEM SIGNIFIES THE FIRST ARTICLE TEST REQUIREMENT (FAT). SEE CLAUSES FOR INFORMATION CONCERNING THE FAT REQUIREMENT. OFFERS THAT DO NOT CITE A PRICE FOR THIS LINE ITEM SHALL BE EVALUATED UNDER THE ASSUMPTION THAT THERE IS NO SEPARATE CHARGE FOR THE FAT. IN THE EVENT THE FAT REQUIREMENT IS WAIVED, NO AWARD WILL BE MADE FOR THIS LINE ITEM. THE NUMBER OF UNITS SHOWN APPEARS AS “1 EA”. THIS QUANTITY SIGNIFIES THE TEST REQUIREMENT. OFFERORS WILL FIND THE ACTUAL QUANTITY REQUIRED BY THE GOVERNMENT FOR THE FAT LINE ITEM PER FAR 52.209-3 OR 52.209-4 IN SECTION A OF THIS SOLICITATION. DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN Need Ship Date:00/00/0000 Original Required Delivery Date:00/00/0000 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 11 OF 26 PAGES CONTINUED ON NEXT PAGE SPE7L3-24-T-201V