INSIGNIA, RANK, OFFIC

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 27 PAGES SPE1C1-23-T-1273 SECTION A Procurement History for NSN/FSC:014680565/8455 CAGE Contract Number Quantity Unit Cost AWD Date Surplus Material . 75556 SPE1C114V0533 2767.000 1.13000 20140908 N 75556 SPM1C112M2435 5000.000 1.09000 20120626 N 43307 SPM1C106M1237 11200.000 0.95000 20060717 N 75556 SPM10005V0004 2500.000 0.99000 20050723 N 7A611 SP010004ASP26D212 2124.000 1.05000 20040218 N 7A611 SP010004ASP26D211 2124.000 1.05000 20040218 N 75556 SP010002ASP49D395 5810.000 1.29000 20020425 N 3A064 SP010001DEE480001 4000.000 1.43000 20010621 N 4A561 SP010001ASP23D042 2625.000 1.44000 20010208 N 7A611 SP010000ASP26D229 2625.000 1.37000 20000803 N 75556 SP010000ASP49D136 2625.000 1.43000 20000511 N CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 27 PAGES SPE1C1-23-T-1273 SECTION B PR: 7000994163 NSN/MATERIAL:8455014680565 ITEM DESCRIPTION

INSIGNIA,RANK,OFFIC "INSIGNIA, RANK, SHOULDER MARK, ROTC,OFFICER, ARMY " CADET LIEUTENANT COLONEL, SMALL " STITCH COUNT 1701 MINIMUM " (BLACK BACKGROUND CLOTH) " DD 22571 B-3-112A 4/8/1991 IOH CARTOON B-3-112-1 11/15/1982 . RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. ADDITIONAL INFORMATION FOR MIL-I-14647: . . CAUTION NOTICE . ALTHOUGH THE DOCUMENT CALLS FOR MORE THAN ONE YARN, ONLY THE ALTERNATE CITED TO RAYON IN THIS CASE POLYESTER, WILL BE CONSIDERED FOR DLA TROOP SUPPORT CONTRACTS. . IN ACCORDANCE WITH MILITARY SPECIFICATION MIL-I-14647. DEVIATIONS TO MIL-I-14647A: . PARAGRAPH 3.3.3.2 RAYON EMBROIDERY YARN. REPLACE ENTIRE PARAGRAPH AS FOLLOWS: RAYON OR POLYESTER EMBROIDERY YARN. THE EMBROIDERY YARN SHALL BE A SEMI-DULL CONTINUOUS FILAMENT, REGENERATED CELLULOSE TYPE RAYON 2 PLY SCHIFFLI TYPE OR MULTIHEAD YARN. THE USE OF 2-PLY POLYESTER IS AUTHORIZED IN LIEU OR RAYON. DENIER AND COLOR OF THE YARN SHALL BE AS SPECIFIED ON THE CARTOON OR DRAWING. THE YARN SHALL SHOW GOOD COLORFASTNESS TO WET DRY-CLEANING. COMPARABLE SIZES ARE AS FOLLOWS: . . SCHIFFLI MULITHEAD RAYON POLYESTER RAYON POLYESTER 150/20 135/2 150/2 35 WT. ---- 100/2 90/2 120/2 40 WT. 120/40 WT. 75/2 70/2 --------- 95/2 . PAGE 6, PARA. 3.5.1, LINE 2 - CHANGE THE FIRST WORD FROM "MACHINE" TO "SCHIFFLI". . AQL REDUCTION: PAGE 9, PARA. 4.7.1, LINE FOUR, DELETE "6.5" AND SUBSTITUTE "4.0" FOR VISUAL. PAGE 10, PARA. 4.7.2, LINE THREE DELETE "6.5" AND SUBSTITUTE "4.0" FOR DIMENSIONAL RESPECTIVELY. CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 27 PAGES SPE1C1-23-T-1273 SECTION B ADDITIONAL INFORMATION FOR MIL-DTL-14651: . INTERIM CHANGES TO MIL-I-14651 ARE AS FOLLOWS; . PARAGRAPH 3.3.1 EMBROIDERY YARNS: SUBSTITUTE THE ENTIRE PARARAPH WITH THE FOLLOWING; "THE EMBROIDERY YARN SHALL BE A SEMI-DULL CONTINUOUS FILAMENT, REGENERATED CELLULOSE TYPE RAYON, TWO-PLYSCHIFFLI TYPE YARN. THE YARN SHALL BE 150, 100 OR 75 DENIER AS SPECIFIED ON THE APPLICABLE CARTOON OR DRAWING. EXCEPT FOR TYPE III AND TYPE VI, STYLE 2, THE USE OF POLY- ESTER IS AUTHORIZED IN LIEU OF THE RAYON. WHEN POLYESTER YARN IS USED, 135 DENIER SHALL BE SUBSTITUTED FOR 150 DENIER, 90 DENIER SHALL BE SUBSTITUTED FOR 100 DENIER AND 70 DENIER SHALL BE SUBSTITUTED FOR 75 DENIER RAYON.". . PARAGRAPH 3.3.4 BOBBIN YARN; AFTER LAST SENTENCE ADD THE FOLLOWING; "EXCEPT FOR TYPE III AND TYPE VI, STYLE 2, A SPUN POLYESTER YARN MAY BE USED.". . ADDITIONAL INFORMATION FOR FED-STD-191: FED-STD-191A NOTICE 7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE FOR NEW DESIGN. WHEN NOT USING FED-STD-191, SEE INTERIM CHANGES TO END ITEM SPECIFICATION FOR REPLACEMENT ASTM. INTERIM CHANGES TO FED-STD-191A: TEST METHOD 5202, PARA. 5.3, DELETE FIRST SENTENCE AND SUBSTITUTE: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH ONE END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT ONE INCH OF SPECIMEN LIES WITHIN THE CLAMP AND ONE INCH OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (FACE OF THE VISE), AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE". TEST METHOD 5309.1 ABRASION RESISTANT OF TEXTILE WEBBING. PAGE 1, PARA 4.1.2,LINE 4: DELETE "B-97" AND SUBSTITUTE "B-91". THE FOLLOWING METHODS ARE IDENTIFIED AS SPECIFYING OZONE DEPLETING SUBSTANCES: 1100, 1200, 1240, 1400, 1410, 1500, 1510,1520,1530, 1540, AND 1550. PARA 5.1 OF THESE TEST METHODS REQUIRE THE USE OF 1,1,1- TRICHLOROETHANE, ALCOHOL OR ETHER. 1,1,1-TRICHLORETHANE IS AN OZONE DEPLETING SUBSTANCE (METHYL CHLOROFORM) AND IS THEREFORE PROHIBITED. THE USE OF EITHER ALCOHOL OR ETHER IS REQUIRED WHEN THESE METHODS ARE IN BASIC OR ANY REFERENCED DOCUMENT. METHOD 5202, STIFFNESS OF CLOTH, DIRECTIONAL; CANTILEVER BENDING METHOD. PAGE 2, PARA. 5.3 DELETE FIRST SENTENCE AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH 1 END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT 1" OF THE SPECIMEN LIES WITHIN THE CLAMP AND 1" OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (INNER FACE OF THE VISE) AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE." METHOD 5556.1, MOBILE LAUNDRY EVALUATION FOR TEXTILE MATERIALS, PAGE 5, PARA. 5.2.2, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACK TEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 45-60 MINUTES OR UNTILSAMPLES ARE DRY IN A ROTATING TUMBLE DRYER." PAGE 5, PARA. 5.2.3, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THEFOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACKTEMPERATURE OF 140-180 DEG. CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 27 PAGES SPE1C1-23-T-1273 SECTION B F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 35-40 MINUTES OR UNTIL SAMPLES ARE DRY." METHOD 5931, ELECTROSTATIC DECAY OF FABRICS; DETERMINATION OF PAGE 1, PARA. 3: AFTER NUMBER OF DETERMINATIONS ADD "PER SAMPLE UNIT". PAGE 1, PARA. 4: DELETE "APPARTUS" AND SUBSTITUTE "APPARATUS". PAGE 1, PARA. 5.1, LINE 3: AFTER "AT" DELETE"APPROXIMATELY". PAGE 2, PARA. 5.2, LINES 2, AND 5: AFTER "OF" ADD "+-". LINE 6: AFTER "TO" ADD "+-". PAGE 2, PARA. 5.3: DELETE IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING:"5.3 MOUNT A SPECIMEN TIGHTLY ACROSS THE ELECTRODES, CENTERING IT OVER THE SENSOR OPENING. THE SURFACE OF THE TEST SPECIMEN (BACK OR FRONT) SHALL FACE THE SENSOR. RECORD (OPTIONAL) THE RESIDUAL CHARGE LEVEL ON THE SAMPLE AS SEEN BY THE SENSOR, INCLUDING POLARITY. NOTE THAT TEST SAMPLES WITH THE RESIDUAL CHARGE LEVELS OF LESS +500 VOLTS YIELD THE BEST RESULTS. APPLY +5000 VOLTS TO THEELECTRODES FOR A PERIOD OF 20 SECS. AT THE END OF THE 20 SECOND PERIOD, THE HIGH VOLTAGE (5000 VOLTS) SHALL BE TURNED OFF ANDTHE SPECIMENS IMMEDIATELY GROUNDED. THE VOLTAGE BEHAVIOR OF THE SPECIMEN WITH RESPECT TO TIME SHALL BE PLOTTED ON THE RECORDER. NOTE: IN SOME CASES, THE TEST EQUIPMENT WILL DISPLAY VOLTAGE AND DECAY TIME INFORMATION AND A CHART RECORDER IS NOT NECESSARY." PAGE 2, PARA. 5.4, LINE 3: DELETE SENTENCE BEGINNING WITH "IF THE SPECIMEN DID" IN ITS ENTIRETY. PAGE 2, PARA. 5.5: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "RECORD THE MAXIMUM VOLTAGE LEVEL(INCLUDING POLARITY) AND DECAY TIME TO 10% OF THE MAXIMUM VOLTAGE LEVEL ACHIEVED." PAGE 2, PARA. 5.6, LINE 1: ADD THE FOLLOWING PRIOR TO 1ST SENTENCE: "REVERSE VOLTAGE POLARITY REPEAT MEASUREMENT, ANDRECORD RESULTS." PAGE 3, PARA. 6.6: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE AVERAGE TIME TO DECAY TO 10%OF THE MAX VOLTAGE SHALL BE INCLUDED FOR EACH OF THE WARP & FILLING DIRECTIONS, AS WELL AS THE OVERALL AVERAGE, FOR EACHFABRIC TESTED. THESE WILL BE OBTAINED BY AVERAGING THE TEST RESULTS (ABSOLUTE VALUE OF) TOGETHER FOR BOTH VOLTAGEPOLARITIES. UNLESS OTHERWISE STATED IN THE REQUIREMENTS DOCUMENT, THE FABRIC SHALL BE CONSIDERED ACCEPTABLE IF THEAVERAGE MAXIMUM VOLTAGE IN BOTH THE WARP AND FILLING DIRECTIONS IS LESS THAN 4000 VOLTS, AND THE AVERAGE DECAY TIME (TO 10% MAXVOLTAGE) IS GREATER THAN 0.5 SECONDS IN BOTH THE WARP AND FILLING DIRECTIONS. IT SHALL BE INDICATED WHETHER THE FABRIC ISACCEPTABLE OR NON-ACCEPTABLE." PAGE 3, PARA. 7.1, SECOND COLUMN, LINE 2: DELETE 406C AND SUBSTITUTE WITH "406D". AFTER PARA. 7.1, ADD THE FOLLOWING: "7.2 NOTE: IF THE MODEL 406D STATIC DECAY METER, OR EQUIVALENT, IS USED, A CHART RECORDER ISNOT MANDATORY FOR THE TEST." (Ref. T0215) ADDITIONAL INFORMATION FOR ASTM-D-6193(2004)OR LATEST VERSION: NO ADDITIONAL INFORMATION FOLLOWS. (Ref. T8068 - May 18, 2006) INSPECTION OF SUPPLIES SHALL BE IN ACCORDANCE WITH FAR PART 52.246-2 STANDARD INSPECTION. ADDITIONAL INFORMATION FOR MIL-STD-105E: MIL-STD-105E, dated 10 May 1989, is hereby canceled. Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product," or ANSI/ASQ Z1.4, "Sampling Procedures and Tables for Inspection by Attributes." CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 27 PAGES SPE1C1-23-T-1273 SECTION B Users are cautioned to evaluate these documents for their particular application before citing it as a replacement document. (Copies of MIL-STD-1916 are available online at http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) (Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207-6028.) ADDITIONAL INFORMATION FOR MIL-STD-1916: NO ADDITIONAL INFORMATION FOLLOWS. (Ref. T8235 - March 1, 2007) FIVE (5) FIRST ARTICLE SAMPLES ARE REQUIRED. FIRST ARTICLE TESTING SHALL BE PERFORMED AND THE CONTRACTOR WILL BE NOTIFIED IN WRITING WITHIN THIRTY (30) CALENDAR DAYS AFTER CONTRACTING OFFICER'S RECEIPT OF FIRST ARTICLE SAMPLES. IAW BASIC SPEC NR MIL-I-14647A(1) NOT 3 REVISION NR 1 DTD 07/21/2001 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 22571 B-3-112A REVISION NR B DTD 04/08/1991 PART PIECE NUMBER: IAW REFERENCE SPEC NR MIL-DTL-14651A NOT 3 REVISION NR A DTD 02/13/2023 PART PIECE NUMBER: IAW REFERENCE SPEC NR MIL-E-17568C NOT 2 REVISION NR C DTD 08/17/2020 PART PIECE NUMBER: IAW REFERENCE STD NR MIL-STD-129R(3) REVISION NR R DTD 02/25/2023 PART PIECE NUMBER: IAW REFERENCE STD NR MIL-STD-1916 NOT 2 REVISION NR DTD 06/05/2014 PART PIECE NUMBER: IAW REFERENCE UNK PPP-B-676E REVISION NR E DTD 12/31/1992 PART PIECE NUMBER: IAW REFERENCE UNK FED-STD-191A(6) NOT 7 REVISION NR A DTD 08/09/2000 PART PIECE NUMBER: IAW REFERENCE NON GOVT STD ASQ Z1.4 (R 2018) REVISION NR DTD 01/01/2003 PART PIECE NUMBER: IAW REFERENCE NON GOVT STD ASTM D5118/D5118M REVISION NR DTD 11/01/2022 PART PIECE NUMBER: IAW REFERENCE NON GOVT STD ASTM D6193-16 REVISION NR DTD 01/01/2016 PART PIECE NUMBER: IAW REFERENCE NON GOVT STD ASTM D1974/D1974M REVISION NR DTD 05/01/2022 PART PIECE NUMBER: CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 10 OF 27 PAGES SPE1C1-23-T-1273 SECTION B CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0001 7000994163 0001 PR 10,000.000 NSN/MATERIAL:8455014680565 DELIVERY (IN DAYS):0117 DELIVER FOB: DESTINATION QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: DESTINATION ACCEPTANCE POINT: DESTINATION PREP FOR DELIVERY: PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999 QUP:001 PRES MTHD:10 CLNG/DRY:0 PRESV MAT:00 WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0 UNIT CONT:ZZ INTRMDTE CONT:ZZ INTRMDTE CONT QTY:ZZZ PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:00 -00 No special marking PRES/PACK LEVELS SHALL BE A/COMMERCIAL IN ACCORDANCE WITH MIL-I-14647 QUANTITY UNIT PACK SHALL BE IN ACCORDANCE WITH MIL-I-14647 UNIT PACKAGING: A PAIR SHALL BE IN PLASTIC BAG. TEN (10) PAIR OF MARKS, OF ONE KIND ONLY, SHALL BE PRESERVED IN A SNUG FITTING FLAT STYLE POLYETHYLENE BAG. THE OPEN END OF BAG SHALL BE FOLDE OVER TAPE OR HEATED SEAL. IN A SET-UP BOX. SIXTY (60) PAIR OF MARKS (6 BAGS OF TEN PAIRS), OF ONE KIND ONLY, SHALL BE PRESERVED LABEL: EACH PAIR AND BAG SHALL BE LABEL AS THE FOLLOWING Bar Code: NSN: Item Name: Quantity Unit Pack: Contract Number: Packing. Level A/B FIFTEEN (15) SET-UP BOXES OF ONE KIND ONLY, SHALL BE PACKED IN A FIBERBOARD SHIPPING CONTAINER AS CITED ON SECTION 5.2.1. NOTE: WHEN THE CONTRACT OR DELIVERY QUANTITY SUPPORTS THE USE OF A PALLET, PALLETIZATION REQUIREMENTS SHALL APPLY. PARCEL POST ADDRESS: UY8615 ARIZONA INDUSTRIES FOR THE BLIND 515 N 51ST AVENUE NUMBER 130 DOCK 1 PHOENIX AZ 85043 CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 11 OF 27 PAGES SPE1C1-23-T-1273 SECTION B PR: 7000994163 PRLI: 0001 CONT’D US FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND CONTRACT FREIGHT SHIPPING ADDRESS: UY8615 ARIZONA INDUSTRIES FOR THE BLIND 515 N 51ST AVENUE NUMBER 130 DOCK 1 PHOENIX AZ 85043 US Need Ship Date:00/00/0000 Original Required Delivery Date:05/28/2023 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *