WEB, STRUCTURAL COMP

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 25 PAGES SPE4A7-23-T-4827 SECTION A Procurement History for NSN/FSC:016502986/1560 CAGE Contract Number Quantity Unit Cost AWD Date Surplus Material . 91750 SPE4A717PA457P00001 8.000 2000.00000 20170530 N This solicitation is being issued under the First Destination Transportation (FDT) program to reduce cost of transportation through the use of Government-Arranged Transportation utilizing Government contracts and rates. Offers should be submitted based on FOB Origin. For offerors whose shipments will orginate from outside the contiguous United States, the offeror's FOB Origin price shall include transportation to a contiguous United States location that the offeror selects based on cost effectiveness or other variables at the offeror's discretion. Additional information about FDT can be found at:

target="_blank">http://www.dla.mil/FDTPI/ CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 25 PAGES SPE4A7-23-T-4827 SECTION B PR: 7000137534 NSN/MATERIAL:1560016502986 ITEM DESCRIPTION WEB,STRUCTURAL COMP WEB,STRUCTURAL COMP RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS) RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER) RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING RT001: MEASURING AND TEST EQUIPMENT MIL-STD-130N(1) DATED 16 NOV 2012. IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. DIGITAL MYLAR DATA EXISTS FOR THIS NSN, AND WILL BE INCLUDED IN THE TECHNICAL DATA PACKAGE PROVIDED BY DLA. IF UNABLE TO USE THE DATA IN THE DIGITAL FORMAT PROVIDED, THE CONTRACTOR WILL BE RESPONSIBLE FOR HAVING THE DATA CONVERTED TO THE NECESSARY FORMAT (I.E. MYLAR FILM), THROUGH A THIRD PARTY AND BEAR THE ASSOCIATED COSTS WHEN CONVERTING FROM DIGITAL TO STABLE BASED FORMAT, THE DIGITAL MYLAR SHALL BE PLOTTED ON STABLE BASE MATERIAL, WHILE MAINTAINING THE DIMENSIONAL ACCURACY DEMANDS OF THE UNDIMENSIONED DRAWING. THIS INCLUDES BUT IS NOT LIMITED TO: VERIFY THE PLOT OF THE MYLAR(S) FOR DIMENSIONAL ACCURACY AS OUTLINED IN ASME Y14.31. ACCURACY SHALL BE DETERMINED VERTICALLY, HORIZONTALLY AND DIAGONALLY. ENSURE THAT THE CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 25 PAGES SPE4A7-23-T-4827 SECTION B INDIVIDUAL GRID UNITS ARE WITHIN THE TOLERANCE OF (+,-) 0.005 INCHES AND (+,-) 0.007 INCHES DIAGONALLY. TOTAL GRID TOLERANCE SHALL BE (+,-) 0.010 INCHES AND (+,-) 0.014 INCHES DIAGONALLY. DRAWINGS WITH DIMENSIONAL ACCURACY POINTS SUCH AS TRAMMEL POINTS SHALL BE MEASURED TO WITHIN CENTERLINE (+,-) 0.010 INCHES AND (+,-) 0.014 INCHES DIAGONALLY. REGISTRATION MARKS SUCH AS THOSE USED ON CIRCUIT CARDS SHALL BE MEASURED TO WITHIN (+,-) 0.005 INCHES AND (+,-) 0.007 INCHES DIAGONALLY. RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. RD002, COVERED DEFENSE INFORMATION APPLIES RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN ENGINEERING NOTES LOADED AS A DRAWING REMARKS: 1. 2-5011 SHEET 1; DASH NO: -2; ENGINEERING NOTES: 1-9 CRITICAL APPLICATION ITEM THE BOEING COMPANY 81205 P/N 2-5011-2 AERO COMPONENTS, LLC 59213 P/N 2-5011-2 NORDAM GROUP LLC, THE 29957 P/N 2-5011-2 D-J ENGINEERING INC 0C7H8 P/N 2-5011-2 MALONES CNC MACHINING INC 2V045 P/N 2-5011-2 CAMNETICS MANUFACTURING CORPORATION 0P657 P/N 2-5011-2 VOLUMATIC INC 1P642 P/N 2-5011-2 INFINITY FABRICATION INC 06DM5 P/N 2-5011-2 FMW, INC. 1QJK4 P/N 2-5011-2 IAW REFERENCE DRAWING NR 81205 BACD2000 REVISION NR R DTD 08/31/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 BAC5300 REVISION NR N DTD 12/05/2016 PART PIECE NUMBER: CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 25 PAGES SPE4A7-23-T-4827 SECTION B IAW REFERENCE DRAWING NR 81205 BAC5300-1 REVISION NR H DTD 06/23/2014 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 BAC5300-2 REVISION NR H DTD 09/15/2014 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98748 20145214 REVISION NR A DTD 04/18/2022 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 2-5011 REVISION NR C DTD 08/24/1958 PART PIECE NUMBER: 2-5011-2 IAW REFERENCE DRAWING NR 81205 BAC5307 REVISION NR U DTD 11/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98748 20145214 REVISION NR A DTD 04/18/2022 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81205 2-5011/2 REVISION NR B DTD 01/01/1939 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 13873 EI-016502986 REVISION NR DTD 10/11/2022 PART PIECE NUMBER: CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE . 0001 7000137534 0001 EA 5.000 NSN/MATERIAL:1560016502986 DELIVERY (IN DAYS):0005 DELIVER FOB: ORIGIN QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN PREP FOR DELIVERY: PKGING DATA-QUP:001 IF MATERIAL IS CONSIDERED HAZARDOUS IAW FED-STD-313, PACKAGE IN ACCORDANCE WITH TQ REQUIREMENT IP025. IF THE MATERIAL IS NOT CONSIDERED HAZARDOUS, IN ACCORDANCE WITH FED-STD-313, THE MATERIAL SHALL BE COMMERCIALLY PACKAGED IN ACCORDANCE WITH ASTM D3951. PARCEL POST ADDRESS: FB2039 FB2039 DD DEPOT OK CNTR RECVG CP 405 855 7075 3301 F AVE DR 22 BLDG 506 TINKER AFB OK 73145-9031 CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 25 PAGES SPE4A7-23-T-4827 SECTION B PR: 7000137534 PRLI: 0001 CONT’D US RDD 777 SHIPMENT. SHIP BY FASTEST TRACEABLE MEANS. DO NOT USE PARCEL POST. FREIGHT SHIPPING ADDRESS: FB2039 FB2039 DD DEPOT OK CNTR RECVG CP 405 855 7075 3301 F AVE DR 22 BLDG 506 TINKER AFB OK 73145 US M/F: (TCN) FB203921101909 RDD: 777 PROJ: AWP TP 1 SUPP ADD: SIG: A FOR GOVERNMENT USE ONLY: (IPD) 03 DIC: A0A DIST: 0A ADV: 6N FC: 6C Need Ship Date:00/00/0000 Original Required Delivery Date:04/25/2022 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 10 OF 25 PAGES CONTINUED ON NEXT PAGE SPE4A7-23-T-4827