SMD_Services_INSTALLATION AND DECOMMISSIONING OF WELLS WITHIN THE FIVE BOROUGHS OF NEW YORK CITY

Description The project Scope of Work Is for the citywide decommissioning of monitoring/ recovery wells as required by 6 NYCRR part 360, Environmental Conservation Law Article 23 and New York State Department of Environmental Conservation CP – 43 policy at various locations in all Five (5) Boroughs as shown in Exhibit A: Location of Wells AND Installation of water wells at various locations in all Five (5) Boroughs of New York City. DECOMMISSIONING METHODS A. The two primary well decommissioning methods are: 1. Grouting in-place. 2. Perforating overdrill. B. In a complex situation, one or more decommissioning procedures may be used for different intervals of the same well. WELL INSTALLATION The wells may be constructed using hollow stem auger, hydraulic reverse rotary, or cable tool (casing hammer) methods. Alternate Construction: Well construction methods other than those described above shall be permitted only after acceptance in writing by THE AUTHORITY. Acceptance of alternate

well construction details does not relieve the Contractor of the responsibility to meet all water quality and quantity requirements of this contract. The minimum borehole diameter shall be two inches greater than the well diameter. Contractor shall ensure that adequate space is available for proper emplacement of the filter pack, bentonite seal and grout. Construction of the monitoring wells must be accomplished without the use of any drilling mud of any type. When reverse rotary drilling is approved, an organic polymer and water drilling fluid may be used. Organic polymer drilling mud may not be used during final construction of the monitoring wells but may be used for preliminary construction of a smaller borehole if all such materials will be reamed out during construction of the final monitoring well. A non-mandatory virtual Pre-Bid Conference will be held on Thursday, March 30, 2023, at 11:00 AM, and will be conducted remotely via Microsoft Teams meeting. Although attendance is not mandatory at the Pre-Bid Conference, it is strongly recommended that all interested Bidders attend, and that Bidders thoroughly review bid documents in advance of the meeting. To participate in the Pre-Bid Conference, please follow the instructions below:Microsoft Teams meeting Join on your computer, mobile app, or room deviceOption 1: Copy and paste the below into your browser: https://teams.microsoft.com/l/meetup-join/19%3ameeting_YjcxNzY2MzctYjkzZC00YzI3LTkxMTYtM2M1NjRiOWZkMmM4%40thread.v2/0?context=%7b%22Tid%22%3a%22709ab558-a73c-4f8f-98ad-20bb096cd0f8%22%2c%22Oid%22%3a%22bcce8bf5-5b21-4315-908d-84e642b9748f%22%7dMeeting ID: 218 065 487 136 Passcode: YKe6cQOption 2: Call in (audio only) +1 646-838-1534,,846891864# United States, New York City Phone Conference ID: 846 891 864#Option 3: Access the attached document “TEAMS Meeting Link RFQ 416990” and click on the embedded link to join.Important dates:Pre-Bid Meeting: March 30, 2023, at 11:00 AMPre-bid Questions Close: April 4, 2023Pre-Bid Answers Shared via Online Discussions: April 10, 2023Bid Closes: April 20, 2023, at 10:00 AMAll vendors are required to participate in NYCHA's MWBE Utilization Plan. Vendors are required to complete and submit at least ONE of the following items by the due date listed: A. MWBE Utilization Plan: Due at time of bid submission OR B. Waiver (or Partial Waiver) of MWBE Utilization Plan: Must be submitted at least Seven (7) days prior to bid due date. (Requests for Partial Waivers MUST also be accompanied by MWBE Utilization Plan) FAILURE TO COMPLETE THE MWBE UTILIZATION PLAN OR WAIVER MAY DEEM YOUR BID NON-RESPONSIVE.Please note that in the event NYCHA receives no responses in connection with this RFQ by the original bid submission deadline, the bid submission deadline shall be extended automatically for seven (7) calendar days. The foregoing extension does not in any way limit NYCHA's right to extend the bid submission deadline for any other reason. Prior to submitting a bid, please confirm that your bid response includes all required forms and documentation and that all required forms and documentation are properly completed, signed, and notarized, where applicable. Note: In response to the COVID-19 outbreak, we are accepting only electronic bids submitted online via iSupplier. Paper bids will not be accepted or considered. Please contact NYCHA Procurement @ procurement@nycha.nyc.gov for assistance. Please note: An Up-to-Date Prevailing Wages Schedule Links are posted on iSupplier under Quick Links Section of Sourcing Supplier. The vendors are responsible for being informed of any updates to the Prevailing Wage Schedule. Request Address 90 Church Street, 6th Floor, New York, NY 10007 Contact Information: Roberta Arnone phone: (212) 306-4690 email: roberta.arnone@nycha.nyc.gov Attachments: Teams Meeting Link RFQ 416990 Other Information: Interested vendors are invited to obtain a copy of the opportunity at NYCHA’s website by going to http://www.nyc.gov/nychabusiness. On the left side, click on “iSupplier Vendor Registration/Login” link. (1) If you have an iSupplier account, then click on the “ Login for registered vendors” link and sign into your iSupplier account. (2) If you do not have an iSupplier account you can request an account by clicking on “New suppliers register in iSupplier” to apply for log-in credentials. Once you have accessed your iSupplier account, log into your account, then choose under the Oracle Financials home page, the menu option “Sourcing Supplier”, then choose “Sourcing”, then choose Sourcing Homepage”; and conduct a search in the “Search Open Negotiations” box for RFQ Number(s) 416990. Note: In response to the COVID-19 outbreak, we are accepting only electronic bids submitted online via iSupplier. Paper bids will not be accepted or considered. Please contact NYCHA Procurement at procurement@nycha.nyc.gov for assistance.