CONTRACTOR FIRST ARTIC

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 37 PAGES SPE7L1-24-T-308B SECTION A SOLICITATION, IN ACCORDANCE WITH PARAGRAPH (d) OF THE CLAUSE AT FAR 52.204-24, REPRESENTATION REGARDING CERTAIN TELECOMMUNICATIONS AND VIDEO SURVEILLANCE SERVICES OR EQUIPMENT, OR IN ACCORDANCE WITH ITS EXISTING REPRESENTATION IN PARAGRAPH (c) OF THE PROVISION AT DFARS 252.204-7016, COVERED DEFENSE TELECOMMUNICATIONS EQUIPMENT OR SERVICES – REPRESENTATION. Caution Notice: Offerors are required to comply with domestic material restrictions. The Berry Amendment, the Buy American Act, and other domestic material restrictions may apply. Offerors are instructed to refer to the solicitation clauses related to foreign sourcing for more information on applicability. The Berry Amendment threshold has been reduced to $150,000 and vendors must carefully review related clauses DFARS 252.225-7006, 252.225-7012, and 252.225-7015 for applicability requirements. If your

offer is based on a non-domestic material, you are required to provide disclosure information in your quote and/or through written notification to the point of contact listed in the solicitation. DoD Class Deviation 2023-O0001: A small business joint venture offeror must submit, with its offer, the representation required in paragraph (c) of FAR solicitation provision 52.212-3, Offeror Representations and Certifications-Commercial Products and Commercial Services, and paragraph (c) of FAR solicitation provision 52.219-1, Small Business Program Representations, in accordance with 52.204-8(d) and 52.212- 3(b) for the following categories: (A) Small business; (B) Service-disabled veteran-owned small business; (C) Women-owned small business (WOSB) under the WOSB Program; (D) Economically disadvantaged women-owned small business under the WOSB Program; or (E) Historically underutilized business zone small business. Contractors shall not provide parts and supplies made using additive manufacturing (AM), unless AM is specifically authorized in the CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 37 PAGES SPE7L1-24-T-308B SECTION A solicitation/contract. See procurement note L31. Procurement History for NSN/FSC:013013213/1015 CAGE Contract Number Quantity Unit Cost AWD Date Surplus Material . 5ZD19 SPE7L124P2853 14.000 5845.88000 20240122 N 28210 SPE7L124P0634 3.000 6480.00000 20231023 N 28210 SPE7L123P8787 2.000 6480.00000 20230813 N 28210 SPE7L123P7858 2.000 6480.00000 20230629 N 28210 SPE7L421P1210P00003 9.000 5900.00000 20210330 N 28210 SPE7L321P2168P00003 3.000 6500.00000 20210128 N 28210 SPE7L420P0286P00001 24.000 5756.00000 20191025 N This solicitation is being issued under the First Destination Transportation (FDT) program to reduce cost of transportation through the use of Government-Arranged Transportation utilizing Government contracts and rates. Offers should be submitted based on FOB Origin. For offerors whose shipments will orginate from outside the contiguous United States, the offeror's FOB Origin price shall include transportation to a contiguous United States location that the offeror selects based on cost effectiveness or other variables at the offeror's discretion. Additional information about FDT can be found at: http://www.dla.mil/FDTPI/ CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 37 PAGES SPE7L1-24-T-308B SECTION B PR: 7006819609 NSN/MATERIAL:1015013013213 ITEM DESCRIPTION BUFFER MECHANISM AS BUFFER MECHANISM AS RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RD001: DEMILITARIZATION: SMALL ARMS WEAPONS AND PARTS AND ACCESSORIES (CATEGORY I - MUNITIONS LIST ITEMS, CATEGORY I-DODM 4160.28-VOL.3) RD002, COVERED DEFENSE INFORMATION APPLIES RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER) RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES RQ016: COMPONENT QUALIFIED PRODUCTS LISTS (QPL)/QUALIFIED MANUFACTURERS LISTS (QML). THIS ITEM CONTAINS ONE OR MORE COMPONENTS DEFINED BY A SPECIFICATION(S) WITH AN ASSOCIATED QUALIFIED PRODUCTS LIST (QPL) OR QUALIFIED MANUFACTURERS LIST (QML). QUALIFICATION REQUIREMENTS IN PROCUREMENT NOTE H02 "COMPONENT QUALIFIED PRODUCTS LIST (QPL)/QUALIFIED MANUFACTURERS LIST (QML)" APPLY. RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 37 PAGES SPE7L1-24-T-308B SECTION B To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. RQ042: Non-Tailored Higher-Level Quality Requirements (ISO 9001:2015) for Manufacturers and Non-Manufacturers RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RT001: MEASURING AND TEST EQUIPMENT SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. This item contains a phosphate coating requirement IAW MIL-STD-171, MIL-DTL-16232, and TT-C-490 Types I, II, and V. In lieu of the required submittal of a preproduction phosphate procedure the following is now required: The contractor responsible for the actual coating procedure must be certified by the Performance Review Institute (PRI) to the NADCAP standard for the phosphate chemical processes. Verification of this certification is required and must be supplied upon request of the Contracting Officer. _______________EXCEPTION DATA____________________ IF DRAWING NOTE GIVES OPTION FOR ZINC OR MANGANESE COATING THEN MANGANESE IS REQUIRED. TDPL: DRAWING 12901103 IS LISTED IN ERROR, PLEASE DELETE DWG 12901103 WITH NO SUBSTITUTES. 12577114 MATERIAL NOTE: FROM: MATERIAL: .28-.46C AISI-SAE ALLOY (4XXX OR 8XXX) STEEL. FREE MACHINING GRADES ARE NOT ALLOWED. TO: MATERIAL: SAE-AISI .28-.46C (4XXX OR 8XXX) ALLOY STEEL BAR PER ASTM A108 OR ASTM A322. MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A108 AND ASTM A322. 12577115 MATERIAL NOTE: FROM: MATERIAL: .27-.46C ALLOY STEEL, AISI 4XXX OR AISI 8XXX. TO: MATERIAL: SAE-AISI .27-.46C (4XXX OR 8XXX) ALLOY STEEL BAR PER ASTM A108 OR ASTM A322. MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A108 AND ASTM A322. CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 37 PAGES SPE7L1-24-T-308B SECTION B 12577117 MATERIAL NOTE: FROM: MATERIAL: .28-.46C ALLOY STEEL, AISI 4XXX OR AISI 8XXX. TO: MATERIAL: SAE-AISI .27-.46C (4XXX OR 8XXX) ALLOY STEEL BAR PER ASTM A108 OR ASTM A322. MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A108 AND ASTM A322. 12577120 MATERIAL NOTE: FROM: MATERIAL: CASTING PER DWG C11577275, COMP 4(>,)> CLASS B & E, OR .23C MAX ALLOY STEEL AISI 4XXX OR AISI 8XXX. TO: MATERIAL: SAE-AISI .23C MAX (4XXX OR 8XXX) ALLOY STEEL BAR PER ASTM A108 OR ASTM A322. OR CASTING PER DWG 11577275, COMP 4, CLASS B & E. MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A108 AND ASTM A322. 12577122 MATERIAL NOTE: FROM: MATERIAL: .13-.34C PLAIN CARBON STEEL, AISI 10XX. TO: MATERIAL: SAE-AISI .13-.34C (10XX) PLAIN CARBON STEEL BAR PER ASTM A311/A311M. MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A311/A311M. 12577123 MATERIAL NOTE: FROM: MATERIAL: CASTING PER DWG C11577275, COMP 4(>,)> CLASS B & E, OR .23C MAX ALLOY STEEL AISI 4XXX OR AISI 8XXX. TO: MATERIAL: SAE-AISI .23C MAX (4XXX OR 8XXX) ALLOY STEEL BAR PER ASTM A108 OR ASTM A322. OR CASTING PER DWG 11577275, COMP 4, CLASS B & E. MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A108 AND ASTM A322. 12577125 MATERIAL NOTE: FROM: MATERIAL: .38-.50C ALLOY STEEL AISI 4XXX OR AISI 8XXX. HOT ROLLED AND ANNEALED. TO: MATERIAL: SAE-AISI .27-.46C (4XXX OR 8XXX) ALLOY STEEL BAR PER ASTM A108 OR ASTM A322. HOT ROLLED AND ANNEALED. MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A108 AND ASTM A322. 12577127 MATERIAL NOTE: FROM: MATERIAL: .28-.46C PLAIN CARBON STEEL, AISI 10XX. TO: MATERIAL: SAE-AISI .28-.46C (10XX) PLAIN CARBON STEEL BAR PER ASTM A311/A311M. MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A311/A311M. CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 10 OF 37 PAGES SPE7L1-24-T-308B SECTION B 12577129 MATERIAL NOTE: FROM: MATERIAL: .28-.50C PLAIN CARBON STEEL, AISI 10XX. CARBON STEEL BAR PER ASTM A311. TO: MATERIAL: SAE-AISI .28-.50C (10XX) PLAIN CARBON STEEL BAR PER ASTM A311/A311M. MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A311/A311M. 12577131 MATERIAL NOTE: FROM: MATERIAL: .27-.46C ALLOY STEEL, AISI 4XXX OR AISI 8XXX. TO: MATERIAL: SAE-AISI .27-.46C (4XXX OR 8XXX) ALLOY STEEL BAR PER ASTM A108 OR ASTM A322. MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A108 AND ASTM A322. 12577140: MATERIAL NOTE: FROM: MATERIAL: .27-.46C ALLOY STEEL, AISI 4XXX OR AISI 8XXX. TO: MATERIAL: SAE-AISI .27-.46C (4XXX OR 8XXX) ALLOY STEEL BAR PER ASTM A108 OR ASTM A322. MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A108 AND ASTM A322. 12901098: MATERIAL NOTE: FROM: MATERIAL: .27-.46C ALLOY STEEL, AISI 4XXX OR AISI 8XXX. TO: MATERIAL: SAE-AISI .27-.46C (4XXX OR 8XXX) ALLOY STEEL BAR PER ASTM A108 OR ASTM A322. MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A108 AND ASTM A322. 12901106: MATERIAL NOTE: FROM: MATERIAL: .27-.46C ALLOY STEEL, AISI 4XXX OR AISI 8XXX. TO: MATERIAL: SAE-AISI .27-.46C (4XXX OR 8XXX) ALLOY STEEL BAR PER ASTM A108 OR ASTM A322. MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A108 AND ASTM A322. 12901107: MATERIAL NOTE: FROM: MATERIAL: .27-.46C ALLOY STEEL, AISI 4XXX OR AISI 8XXX. TO: MATERIAL: SAE-AISI .27-.46C (4XXX OR 8XXX) ALLOY STEEL BAR PER ASTM A108 OR ASTM A322. MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A108 AND ASTM A322. 12901164: MATERIAL NOTE: FROM: MATERIAL: .27-.46C ALLOY STEEL, AISI 4XXX OR AISI 8XXX. TO: MATERIAL: SAE-AISI .27-.46C (4XXX OR 8XXX) ALLOY STEEL BAR PER ASTM A108 OR ASTM A322. CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 11 OF 37 PAGES SPE7L1-24-T-308B SECTION B MERCHANT QUALITY OR FREE MACHINING GRADES ARE NOT ALLOWED. TDPL: ADD ASTM A108 AND ASTM A322. PD12577113 IN BLOCK 4 CHANGE THE NATIONAL STOCK NUMBER FROM: 1015-01-301-3212 TO: 1015-01-301-3213 TDPL sheet 14: FROM: TT-L-50 TO: MIL-PRF-81352 Drawing 12577134 note 5: FROM: TT-L-50 TO: MIL-PRF-81352 Drawing 12577118 note 4: FROM: Marking requirements per MIL-C-13931 X Do apply: 19206 ASSY 12577118 MFR- MANUFACTURE CAGE CODE TO: Marking requirements per MIL-STD-130 X Do apply: 19206 ASSY 12577118 CDA-1NUW7 MFR SPECIAL INSPECTION EQUIPMENT The Government Special Inspection Equipment (SIE) design drawings, cited in the Quality Assurance Provisions (QAPs), are no longer being maintained by the Government and may not reflect the latest component configuration and are, therefore(>,)> included for informational purposes only. GAGE The TDP contains gage drawings that are to be considered "For Informational Purposes Only" and are not up to date with the latest drawing revision. The use of gages is optional and not a requirement. Wherever applicable, delete all references to gages and replace with Standard Measuring & Test Equipment. In addition, these gage drawings should be removed from TDP. AIE All Government AIE (EL Documents) designs which are cited in the Technical Data Package List or in any of the documents in the technical data package are no longer being maintained by the Government, may not reflect the latest component configuration and are, therefore, included for informational purposes only. PROTECTIVE FINISH CONFLICTS In cases where on the SAME component, drawings 8769470 and 7309999 are specified and there is a conflict between the reference 'MIL-DTL-16232(>,)> TYPE M or Z, Class 2' and 'MIL-DTL-16232, TYPE M or Z, Class 1', the requirements of drawing 8769470 will apply. QAP 7309999 REFERENCES WITHIN QAPS