SPECIAL TESTING

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 37 PAGES SPE4A6-24-Q-0831 SECTION B SUPPLY/SERVICE: 1670-01-567-2205 CONT'D Z1.4-2008, LEVEL S-2, Table II-A, SINGLE SAMPLING PLANS FOR NORMAL INSPECTION, NO AQL WILL BE USED (per Engineering Support Activity, ESA). SELECTED AT RANDOM BY THE COGNIZANT GOVERNMENT REPRESENTATIVE. FOLLOW E04 FOR SHIPPING INSTRUCTIONS. PRIOR TO OR AT THE SUBMITTING OF THE FIRST ARTICLE TEST EXHIBITS, THE CONTRACTOR SHALL PROVIDE (AS APPLICABLE): A) 5 SQUARE YARDS OF EACH TYPE OF FABRIC. B) 1/2 LB. SPOOL, CONE, OR TUBE OF EACH TYPE OF THREAD. C) 15 YARDS OF EACH TYPE OF CORD, WEBBING, AND TAPE. D) 2 EACH OF ALL HARDWARE USED IN CONSTRUCTION OF SUBJECT ITEM ALL MATERIAL CERTIFICATIONS MUST ALSO BE PROVIDED. CONTRACTOR SHALL MARK THE CONTAINER "ATTENTION TEXTILE TESTING MONITOR" MARK THE NSN AND CONTRACT NUMBER ON THE SHIPPING LABEL. NOTE: ANY CHANGE IN SUPPLIES/SUPPLIERS MUST BE TESTED AND APPROVED. Government

First Article Preproduction approval required. Testing will be in accordance with applicable drawings, specifications and/or Engineering instructions. The first article offered shall be manufactured at the facilities in which production quantities are procured and produced under this contract. When submitting the first article(s) for government testing, a copy of the contract and all applicable drawings, specifications, engineering instructions, certifications, and inspection sheets shall be provided. Upon receipt and evaluation of the test report from the responsible government testing location, the contracting officer will provide final notification to the manufacturer. Any questions or concerns regarding the first article test requirements must be submitted through the contracting officer. Additional Wide Area Workflow (WAWF) instructions for government first article test CLIN: The contractor shall code the receiving report for government first article test CLIN in WAWF as Follows: A: Inspection at origin (Source) - Enter the DCMA office DODAAC listed on page 1 of the contract. B: Acceptance by other - Enter the issue by office DODAAC listed on page 1 of the contract. C: Ship to code - Enter the DODAAC of the test facility listed for the government first article test CLIN in the contract (See FAR Clause 52.209-4). FIRST ARTICLE TEST MARKING INSTRUCTIONS: FAT sample(s) packaging shall be clearly marked "FIRST ARTICLE TEST EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contrasting color to the packaging. Marking shall be located adjacent to the Package Shipping Label side and on at least one additional side of the package. MIL-STD-130N(1) DATED 16 NOV 2012. IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY THIS IS AN ARMY IDENTIFIED CRITICAL SAFETY ITEM. . ALL REQUESTS FOR WAIVERS OR DEVIATIONS CLASSIFIED AS CRITICAL, MAJOR, OR MINOR MUST BE FORWARDED TO THE DSC CONTRACTING OFFICER FOR REVIEW AND APPROVAL. . ALL ITEMS OF SUPPLY SHALL BE MARKED IAW MIL-STD-129. IN ADDITION, EACH UNIT PACK WILL BE MARKED WITH LOT AND SERIAL NUMBER (IF AVAILABLE), CONTRACTOR'S CAGE CODE, ACTUAL MANUFACTURER'S CAGE CODE AND PART NUMBER. 1. "AWARDEE MUST PROVIDE COMPLETED DD1222 FORM WITH EVERY ESA (RE)SUBMISSION." CRITICAL APPLICATION ITEM IAW BASIC DRAWING NR 81337 11-1-7059 REVISION NR D DTD 03/16/2022 PART PIECE NUMBER: 11-1-7059-1 IAW REFERENCE DRAWING NR 81337 11-1-7196 CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 37 PAGES SPE4A6-24-Q-0831 SECTION B SUPPLY/SERVICE: 1670-01-567-2205 CONT'D REVISION NR G DTD 04/24/2017 PART PIECE NUMBER: IAW REFERENCE QAP 13873 QAP-MLSE-AVNFAZ-12073 REVISION NR DTD 03/13/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81337 11-1-7110 REVISION NR B DTD 04/20/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81337 11-1-7182 REVISION NR A DTD 04/04/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81337 11-1-7059 REVISION NR B DTD 03/16/2022 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81337 11-1-7110 REVISION NR A DTD 09/18/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81337 11-1-4179 REVISION NR R DTD 09/07/2022 PART PIECE NUMBER: IAW REFERENCE QAP 13873 11-1-7059-1 REVISION NR DTD 01/19/2016 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81337 11-1-7059-1 REVISION NR DTD 08/15/2023 PART PIECE NUMBER: Critical Safety Item ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT . 0001 1670-01-567-2205 976.000 EA $ ________________ $ ________________ SLIDER PANEL,T11 MA PRICING TERMS: Firm Fixed Price QTY VARIANCE: PLUS 0% MINUS 0% INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN FOB: ORIGIN DELIVERY DATE: 205 DAYS ADO PREP FOR DELIVERY: PKGING DATA - MIL-STD-2073-1E QUP:001 PRES MTHD:33 CLNG/DRY:1 PRESV MAT:00 WRAP MAT:00 CUSH/DUNN MAT:NA CUSH/DUNN THKNESS:C UNIT CONT:E5 OPI:M INTRMDTE CONT:E5 INTRMDTE CONT QTY:AAA PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:32 -32 Type I, shelf life PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT FAT sample(s) packaging shall be clearly marked "FIRST ARTICLE TEST EXHIBIT(S) DO NOT POST TO STOCK!!!" in largest font possible with contrasting color to the packaging. Marking shall be located adjacent to the Package Shipping Label side and on at least one additional side of the package. PARCEL POST ADDRESS: CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 37 PAGES SPE4A6-24-Q-0831 SECTION B SUPPLY/SERVICE: 1670-01-567-2205 CONT'D W25G1U W1A8 DLA DISTRIBUTION DDSP NEW CUMBERLAND FACILITY 2001 NORMANDY DRIVE DOOR 113 TO 134 NEW CUMBERLAND PA 17070-5002 US FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND CONTRACT FREIGHT SHIPPING ADDRESS: W25G1U W1A8 DLA DISTRIBUTION DDSP NEW CUMBERLAND FACILITY 2001 NORMANDY DRIVE DOOR 113 TO 134 NEW CUMBERLAND PA 17070-5002 US Special Testing ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT . 0002 0001 - S00000040 1.000 EA $ ________________ $ ________________ PRICING TERMS: Firm Fixed Price INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN FOB: ORIGIN DELIVERY DATE: 30 DAYS ADO PREP FOR DELIVERY: Not Applicable Government First Article Test Government First Article Test – The number of units shown signifies the test requirement. See FAR clause 52.209-4 for the actual quantity required to be tested. ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT . 0003 0001 - S00000052 1.000 EA $ ________________ $ ________________ PRICING TERMS: Firm Fixed Price FOB: DELIVERY DATE: 255 DAYS ADO PREP FOR DELIVERY: Not Applicable Production Lot Testing (Government) ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT . 0004 0001 - S00000061 1.000 EA $ ________________ $ ________________ PRICING TERMS: Firm Fixed Price INSPECTION POINT: ORIGIN ACCEPTANCE POINT: ORIGIN FOB: ORIGIN DELIVERY DATE: 30 DAYS ADO CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 37 PAGES SPE4A6-24-Q-0831 SECTION B SUPPLY/SERVICE: 0001-S00000061 CONT'D PREP FOR DELIVERY: Not Applicable GOVT USE External External External Customer RDD/ ITEM PR PRLI PR PRLI Material Need Ship Date . 0001 7006519253 0001 N/A N/A N/A 03/25/2025 0002 N/A N/A N/A N/A 9910 N/A 0003 N/A N/A N/A N/A N/A N/A 0004 N/A N/A N/A N/A N/A N/A * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 9 OF 37 PAGES CONTINUED ON NEXT PAGE SPE4A6-24-Q-0831 SECTION A - SOLICITATION/CONTRACT FORM 52.204-16 COMMERCIAL AND GOVERNMENT ENTITY CODE REPORTING (AUG 2020) FAR SECTION C - SPECIFICATIONS/SOW/SOO/ORD C03 CONTRACTOR RETENTION OF SUPPLY CHAIN TRACEABILITY DOCUMENTATION (MAR 2023) C01 SUPERSEDED PART NUMBERED ITEMS (SEP 2016) C14 CORRECTION OF NONCONFORMING PACKAGING OR MARKING (MAY 2020) C02 MANUFACTURING PHASE OUT OR DISCONTINUATION OF PRODUCTION, DIMINISHING SOURCES, AND OBSOLETE MATERIALS OR COMPONENTS (DEC 2016) SECTION E - INSPECTION AND ACCEPTANCE E08 FIRST ARTICLE TESTING REQUIREMENTS (JAN 2024) (1) If there is not a separate contract line item number (CLIN) for FAT, the offeror shall include all costs and risk associated with completion of the FAT requirement in the production CLIN price. (2) If there is a separate FAT CLIN, the offeror shall include all costs and risk associated with completion of the FAT requirement in the FAT CLIN price. The unit of issue for the FAT CLIN, EACH, is equal to one First Article Test (1EA=1FAT). To receive payment for any costs associated with FAT, the offeror shall propose costs associated with FAT on a separate CLIN. The offeror shall base the production CLIN price solely on all costs associated with completion of the production units and shall exclude all FAT-related costs. (3) The contracting officer will use the total award price in selecting the best value offer from among all eligible offerors. However, for an offeror to be eligible for award, the contracting officer must determine that the FAT CLIN price (unless FAT is waived) and the production CLIN price are fair and reasonable; and, if set-aside under FAR Part 19, a fair market price. The offeror shall not propose a FAT CLIN price that is materially unbalanced in relation to the production CLIN price. In the event an offeror receives a waiver of the FAT require3ment, the contracting officer will deduct the FAT CLIN price for the waived source in determining the total award price. (4)(a) Notwithstanding the conditions for waiving first article, the contracting officer may order an additional first article sample, or portion thereof, in writing if there is a -- (i) Major change to the technical data; (ii) Lapse in production for a period in excess of 90 days; or (iii) Change in the place of performance (manufacturing facility), manufacturing process,material used, drawing, specification or source of supply. (b) When conditions in paragraphs (4)(a)(i), (ii), or (iii) occur, the contractor shall notify the contracting officer; who will determine whether to order an additional first article sample or portion thereof and provide instructions concerning the submission, inspection, and notification of results. The contractor shall bear the costs of the additional first article testing resulting from any of the causes in paragraphs (4)(a)(i)-(iii) instituted by the contractor and not due to changes directed by the Government. (5) Waivers. The offeror may submit a request for FAT waiver to the contracting officer, who may waive the FAT requirement when all of the following criteria apply: (a) The offeror requesting waiver has manufactured and delivered the item or a similar item within the last three (3) years regardless of item criticality. The offeror shall provide the following information and be prepared to provide documentary evidence upon the contracting officer's request: (i) Contract number(s), date(s), and issuing Government agency or agencies. (ii) Description of item previously furnished, identified by part number, type, model number and/or other identifying information. If the item previously furnished is similar but not identical to the item being acquired under the current buy, the offeror shall explain why manufacture of the item previously furnished is sufficient to demonstrate its ability to manufacture the item being acquired under the current buy without need for a first article test. (iii) Engineering control document/change number of item previously furnished. (b) There have been no changes to manufacturing processes, tooling, or place of performance. (c) There have been no changes to manufacturing data (e.g., drawing revisions that change materials, dimensions, processes, inspection or testing requirements; or subcontractors used to manufacture the items successfully in the past). (d) The offeror shall supply an item of the same design and manufactured by the same method at the same facilities as the item or similar item previously furnished and accepted under subparagraph (5)(a) (6) Contractor-Performed FAT. (a) The contractor shall test the quantities as outlined in paragraph (a) of FAR clause 52.209-3 as specified in the contract. The contractor shall submit reports in accordance with paragraph (b) of FAR clause 52.209-3, as supplemented in this procurement note. (b] For test report preparation and delivery of contractor FAT, the contractor shall -- (i) Use the data item description DI-NDTI-80809B report format. (ii)] Mark the test report with the following: “First article test report - Contract number:[ ] and lot/item number: [ ]. (iii) Sign the FAT Report, accompanied by the system of record receiving report (i.e, WAWF or] DD Form 250) and contractor confirmation that the same CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 10 OF 37 PAGES CONTINUED ON NEXT PAGE SPE4A6-24-Q-0831 SECTION E - INSPECTION AND ACCEPTANCE (CONTINUED) process and facilities used to manufacture the first article units will be used to manufacture the production units, to the contracting officer at the applicable address shown below: (A) For awards issued by DLA Aviation; or DLA Troop Support Clothing and Textile (C&T), Medical Materiel, or Subsistence, submit the report to the procuring activity in Block 6 of the DD Form 1155, Block 7 of Standard Form (SF) 33, Block 5 of SF 26, or Block 9 of SF 1449 award. (B) For awards issued by DLA Land (SPE7L), submit the report to the following address: DLA Land - FLSEB ATTN: FAT Monitor P. O. Box 3990 Columbus, OH 43218-399, or email to: Land.FAT.Monitor@dla.mil. (C) For awards issued by DLA Maritime (SPE7M), submit the report to the following address: DLA Maritime - FMSE ATTN: FAT Monitor P. O. Box 3990 Columbus, OH 43218-3990, or email to: maritime.fat.monitor@dla.mil. (D) For awards issued by DLA Troop Support Construction and Equipment (SPE8E), email the report to Construction and Equipment FAT Monitor at trpsptcandefatmonitor@dla.mil. If report exceeds email limitations, submit the report to the following address: DLA Troop Support ATTN: First Article Testing Monitor Building 3, 700 Robbins Avenue Philadelphia, Pennsylvania 19111. Preferred electronic submissions: Hardware FAT Monitor at DLAHardwareFATMonitor@dla.mil. (7) The contractor shall -- (a) Provide and maintain an inspection system acceptable to the Government in accordance with FAR Clause 52.246-2 or 52.246-3; (b) Maintain and make available all records evidencing those details at the Government's request. (c) At least fourteen (14) calendar days (or as otherwise specified in the contract) prior to shipment to the Government, provide written notice to the contracting officer and to the cognizant DCMA Functional Specialist when full administration or Quality Support administration is delegated to DCMA. (8) Government-performed FAT. The contractor shall -- (a) For delivery of separately priced Government first article samples for Government performed FAT ship the units and system of record receiving report (i. e., WAWF or DD Form 250) to the test facility specified in paragraph (a) of FAR clause 52.209-4. (b) For delivery of Government first article samples that are not separately priced, ship the units with a commercial shipping document to the test facility. (c) Prepare the shipping container(s) by marking the external packages in bold letters, “First Article Exhibits - Do Not Post to Stock," adjacent to the MIL- STD-129 (latest revision) identification markings. (d) Use a hard copy of the system of record receiving report (i.e., WAWF DD Form 250), or commercial shipping document as a packing list, in accordance with DFARS Appendix F. (e) Mark the exterior of the shipping container in accordance with MIL-STD-129 (latest revision), paragraph 5.11. (f) In the interior package, include hard copies of the contract, test reports, material certifications/process operation sheets, drawings used to manufacture the units, and a pre-paid return label or shipping account for payment. (g) Send units by traceable means (e.g., certified or registered mail, United Parcel Service, Federal Express). (h) Send an email with subject titled “Notification of Test Exhibits [ ]” to the corresponding address in (i) or (ii) below and to the contracting officer specified in the contract. In the email, provide the shipment date, contract/purchase order number, National Stock Number, means of transportation, tracking number, and summary of container contents. Attach a copy of the system of record receiving report (i.e., WAWF or DD Form 250) documenting the Government has performed the contract quality assurance within the system or record. (i) DLA Land & Maritime - DSCCProdVerif@dla.mil (ii) DLA Aviation - DSCR.Test & EvaluationOffice@dla.mil (9) At its discretion, the Government may return FAT units to the contractor at no cost to the Government. The contractor shall submit the return address and pre-paid return label or shipping account for payment. (10) If the Government disapproves or conditionally approves Government-performed FAT units, the Government will take action in accordance with FAR 52.209-4. E02 SUPPLEMENTAL FIRST ARTICLE EXHIBIT DISPOSITION – GOVERNMENT MAINTAINED (MAY 2020) E10 GOVERNMENT FIRST ARTICLE TEST (FAT) INFORMATION (JUL 2022) (1) For FAT requirements, the Government will conduct inspection at source and acceptance at destination. The FOB point is destination. Due to known systems limitations, solicitations may contain erroneous inspection, acceptance, and FOB points. This procurement note takes precedence over any conflicting terms. (2) GOVERNMENT FAT DELIVERY SCHEDULE (a) Days: To Deliver FAT Units to the Government (b) Days: Government FAT Evaluation and Notification to Contractor (c) Days: To Deliver Final Production Quantity After Approval of FAT. If PLT applies, this line will be blank; the number of delivery days for final production quantity will appear in procurement note E03, Production Lot Testing - Contractor, or E04, Production Lot Testing - Government, as applicable] (d) Total Delivery Days for FAT (Sum of Paragraphs (2)(a) through (2)(c)). CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 11 OF 37 PAGES CONTINUED ON NEXT PAGE SPE4A6-24-Q-0831 SECTION E - INSPECTION AND ACCEPTANCE (CONTINUED) 52.246-2 INSPECTION OF SUPPLIES FIXED PRICE (AUG 1996) FAR 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014) FAR As prescribed in 46.311, insert the following clause: (a) The Contractor shall comply with the higher-level quality standard(s) listed below. Title Number Date Tailoring [Contracting Officer insert the title, number, date, and tailoring (if any) of the higher-level quality standards.] (b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph (a) of this clause and the requirement to flow down such standards, as applicable, to lower-tier subcontracts, in- (1) Any subcontract for critical and complex items (see 46.203(b) and (c)); or (2) When the technical requirements of a subcontract require- (i) Control of such things as design, work operations, in-process control, testing, and inspection; or (ii) Attention to such factors as organization, planning, work instruction, documentation control, and advanced metrology. (End of Clause) E05 PRODUCT VERIFICATION TESTING (MAY 2020) (1) Product verification testing (PVT) under this procurement note will only apply when the contracting officer specifically invokes it in writing. The contracting officer may invoke PVT at or after contract award. If the contracting officer invokes PVT at contract award, the contract will explicitly state this testing requirement. If the contracting officer invokes PVT after contract award, the contracting officer shall notify the contractor and the cognizant DCMA ACO. The Government will perform PVT testing at a Government-designated testing laboratory. (2) The contractor shall not ship or deliver any material until it receives notification of the acceptable PVT results, unless the contracting officer directs it to do so in writing The Government will provide the PVT results to the contractor within 20 business days after receipt at the Government testing facility, unless the Government specifies otherwise in writing. (3) The contractor shall provide and maintain an inspection system acceptable to the Government in accordance with FAR Clause 52.246-2 or 52.246-3; and maintain and make available all records evidencing those details if requested by the Government. When the Government finds evidence of risk associated with the contractor's sampling process, the Government may witness and evaluate the contractors sampling process. The contractor shall randomly select samples from the production lot(s), unless the contracting officer specifies otherwise in writing. The contractor shall ship the selected PVT samples with a copy of the system of record receiving report (i.e., WAWF, DD Form 250, or commercial shipping document) and the contractor's signed DD Form 1222. The contractor shall prepare the shipping container(s) by marking the external packages in bold letters, “Product Verification Test Samples - Do Not Post to Stock," Contract Number [ ] and Lot/Item Number [ ]” adjacent to the MIL-STD-129 (latest revision) identification markings. The contractor shall use a hard copy of the system of record receiving report as a packing list, in accordance with DFARS Appendix F. The contractor shall mark the exterior of the shipping container in accordance with MIL-STD129 (latest revision), paragraph 5.11. The contractor shall send samples by traceable means (e.g., certified or registered mail, United Parcel Service, Federal Express). The contractor shall include the following in the interior package: (a) Hard copies of the contract; (b) Material certifications/process operation sheets; and (c) Drawings used to manufacture the units and return shipping information. (4) The Government will return samples that pass testing and are not destroyed during evaluation to the contractor at the Government's expense for the contractor to include as part of the total contract quantity to be delivered under the contract. The contractor and Government may agree to dispose of samples not destroyed when the cost of the item does not justify the shipping expense. If the Government does not return approved samples that pass testing to the contractor, the Government will consider those samples as part of the contract quantity for payment and delivery. (5) If samples fail testing, the Government may reject the entire contract lot from which the contractor took the samples. The Government may, at its discretion, retain samples that fail testing without obligation to the contractor. E06 INSPECTION AND ACCEPTANCE AT SOURCE (JUN 2018) Inspection and acceptance are at source. The place of acceptance is the location where the Government conducts the last inspection before shipment, unless the contractor indicated a different physical location for acceptance below. The contractor shall indicate the location where supplies will be inspected, if different from the production location: Commercial and Government Entity (CAGE) code: Address: Applicable to contract line item numbers(s) (CLIN(s)): The contractor shall indicate the location where packaging will be inspected, if different from the production location: [ ] Same as for supplies OR CAGE code: Address: Applicable to CLIN(s): The contractor shall indicate the location where supplies will be accepted, if different from the inspection location: Commercial and Government Entity (CAGE) code: