INSIGNIA, GRADE, ENLI

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 5 OF 36 PAGES SPE1C1-22-T-1693 SECTION B PR: 0096066760 NSN/MATERIAL:8455016886267 ITEM DESCRIPTION INSIGNIA,GRADE,ENLI INSIGNIA, EMBROIDERED, ENLISTED PERSONNEL ARMY PRIVATE, FULL COLOR, LARGE, AGSU PUTTY HCW 67197/OLIVE DRAB HAH 67133 ON HERITAGE GREEN 564, ROLL NUMBER 3961 ATTACHMENT METHOD: SEW-ON OVEREDGE STITCHING REQUIRED. STITCH COUNT IS 1710 STITCHES MINIMUM. TYPE I, SIZE 1, STYLE 2, CLASS 11 DRAWING B-3-17 09/12/2008 DRAWING B-3-8A, 08/16/1996 CONSTRUCTION AND DETAIL CARTOON B-3-17M 07/08/1977 RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES ADDITIONAL INFORMATION FOR MIL-DTL-14651A: . . CAUTION NOTICE THE DEPARTMENT OF DEFENSE IS PROHIBITED BY THE PROVISIONS OF THE BERRY AMENDMENT FROM PROCURING ITEMS OF CLOTHING THAT HAVE NOT BEEN GROWN OR PRODUCED IN THE UNITED STATES OR ITS POSSESSIONS. ALTHOUGH THE DOCUMENT CALLS FOR MORE THAN ONE YARN, ONLY THE ALTERNATE CITED TO RAYON IN THIS CASE POLYESTER, WILL BE CONSIDERED FOR DLA TROOP SUPPORT CONTRACTS. IF OTHER THAN SCHIFFLI EMBROIDERY MACHINE IS USED, THE STITCH COUNT ON GOVERNMENT CARTOON MUST BE DOUBLED. . INSIGNIA SHALL BE FABRICATED IN ACCORDANCE MIL-DTL 14651A DATED, 22 OCTOBER 2001 AND APPLICABLE CARTOON AND DRAWING. PAGE 10, PARAGRAPH 3.3.5.1 EXCEPT TYPE III, STYLE 3 (MARINES,DRESS AND BAND DRESS)AND 4, AND TYPE VI STYLE 2(INSIGNIA,STRIPES,SERVICES, MARINE CORPS). THE BASE CLOTH FOR ALL INSIGNIA EXCEPT THOSE LISTED ABOVE, SHALL BE 100% COTTON, 50/50 POLYESTER/COTTON, OR 65/35 POLYESTER/COTTON, THREE UP, ONE DOWN, LEFT HAND TWILL, 7.0 TO 8.3 OUNCES PER SQUARE YARD, SINGLE FLY WARP AND FILLING, WITH A BREAKING STRENGTH OF NOT LESS THAN 150 LBS. . INTERIM CHANGES TO MIL-DTL-14651A ARE AS FOLLOWS: CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 6 OF 36 PAGES SPE1C1-22-T-1693 SECTION B PAGE 2 UNDER COLUMN TYPE IV GENERAL OFFICER AFTER STYLE 6, ADD "STYLE 7, AIR FORCE BATTLE UNIFORM (ABU) GREY SUBDUED FOR CLASS 1-4, SIZE 1". PAGE 2 UNDER COLUMN TYPE V, AFTER STYLE 4, ADD "STYLE 6, AIR FORCE BATTLE UNIFORM(ABU) GREY SUBDUED FOR CLASS 1-6". PAGE 3, UNDER COLUMN TYPE VIII, AFTER STYLE 3 ADD "STYLE 4", AIR FORCE BATTLE UNIFORM(ABU) GREY SUBDUED." PAGE 4, UNDER COLUMN TYPE X AFTER STYLE 4 ADD "STYLE 6, AIR FORCE BATTLE UNIFORM (ABU) GREY SUBDUED". PAGE 4, UNDER COLUMN TYPE XII AFTER STYLE 2 ADD "STYLE 3, AIR FORCE BATTLE UNIFORM (ABU) GREY SUBDUED". PAGE 6, BASE CLOTH AT THE END OF PARAGRAPH ADD, "US AIR FORCE OCCUPATIONAL BADGES FOR ABU SHALL BE EMBROIDERED ON 100% TEXTURIZED POLYESTER TWILL BASE CLOTH MATCHING AIR FORCE GREY 1640"." PAGE 7, PARA 3.1 FIRST ARTICLE. AT THE END OF OF PARA. ADD " THE FIRST ARTICLE SHALL BE BEST QUALITY PRE-PRODUCTION SAMPLES. THE FIRST ARTICLE SAMPLES MUST PACKAGED AND LABELED IN THE SAME MANNER AS THE CONTRACT UNIT QUANTITY"." PAGE 9, TYPE VIII ADD "STYLE 4" SAME LINE NEXT COLUMN ADD "AF Grey 1640, SAME LINE NEXT COLUMN ADD "DARK BLUE 67126". PAGE 10, ADD NOTE 4/ MARS GREEN 9129 MAY BE AVAILABLE AT ROBISON ANTON CORPORATION. PAGE 11, TYPE VIII ADD "STYLE 4" SAME LINE NEXT COLUMN ADD "AF Grey 1640, SAME LINE LAST COLUMN ADD "5484 LIGHT MOSS". PAGE 15, PARA. 4.1 A. FIRST ARTICLE INSPECTION. AT THE END OF PARA. ADD "THE FIRST ARTICLE INSPECTION SHALL CONSIST OF VISUAL EXAMINATION OF END ITEM, EXAMINATION FOR DIMENSIONS AND END ITEM TESTING." . PARA. 4.1 B. CONFORMANCE INSPECTION. AT THE END OF PARA. ADD THE FOLLOWING: "THE CONFORMANCE INSPECTION SHALL CONSIST OF VISUAL EXAMINATION OF END ITEM AND EXAMINATION FOR DIMENSIONS. PAGE 16, PARA 4.3.1 TESTING OF COMPONENTS. AT END OF PARA. ADD THE FOLLOWING: " AS PER CONTRACT, THE SAMPLE SIZE SHALL BE THREE UNITS FOR EACH TEST CHARACTERISTIC OF EACH COMPONENT. THE LOT SHALL BE UNACCEPTABLE IF ONE OR MORE UNITS FAIL TO MEET THE REQUIREMENTS IN TABLE III.". . PAGE 17,PARA. 4.3.2 VISUAL EXAMINATION. AT THE END OF PARA ADD THE FOLLOWING: "DEFECTS SHALL BE EXPRESSED IN DEFECTS PER HUNDRED UNITS. THE INSPECTION LEVEL SHALL BE II. THE ACCEPTABLE QUALITY LEVEL SHALL BE .40 FOR MAJOR AND 1.0 FOR MAJOR CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 7 OF 36 PAGES SPE1C1-22-T-1693 SECTION B AND MINOR DEFECTS COMBINED.". . PAGE 19, PARA. 4.3.3 EXAMINATION FOR DIMENSIONS. AT THE END OF PARA. ADD THE FOLLOWING: "THE DEFECTS SHALL BE EXPRESSED IN DEFECTS PER HUNDRED UNITS. THE INSPECTION LEVEL SHALL BE S3. THE ACCEPTABLE QUALITY LEVEL SHALL BE 1.5 FOR MAJOR DEFECTS. THE FIRST ARTICLE WILL BE REJECTED IF THE END ITEM HAVE ANY MAJOR DEFECTS.". . PAGE 20, PARA. 4.3.4 END ITEM TESTING. AT THE END OF THE PARA. ADD THE FOLLOWING: "AS PER THE CONTRACT, THE SAMPLE SIZE SHALL BE 24 INSIGNIA OR ONE STRIP FOR INSIGNIA FURNISHED IN STRIPS. THE LOT SHALL BE UNACCEPTABLE IF ONE OR MORE UNITS FAIL TO MEET THE REQUIREMENTS IN TABLE V" . PARAGRAPH 6.3 SAMPLES, DELETE IN ITS ENTIRETY. . PAGE 21 PARA. 6.6 SUGGESTED UNIT PACKAGING. AT THE END OF PARA. ADD THE FOLLOWING: " THE SUGGESTED BUNDLE QUANTITY SHALL BE PLACED INTO A POLYETHYLENE BAG AND HEAT SEALED OR TAPE CLOSED. THE BUNDLE SHALL BE MARKED IN ACCORDANCE WITH MIL-STD-129. . PAGE 21, PARAGRAPHS 6.6.2, 6.6.3 AND 6.6.4 AT THE END OF THESE PARAGRAPHS ADD: "FOR INSIGNIAS WITH A HOOK FASTENER TAPE BACKING, THE INSIGNIAS SHALL BE PUT UP IN BUNDLES OF TWENTY EACH.". . PAGE 22, ADD NEW PARAGRAPH: "6.6.6.1 PACKAGING. PACKAGING SHALL BE IN ACCORDANCE WITH ASTM D 3951 WITH THE FOLLOWING EXCEPTIONS: A TOTAL OF EIGHT (8) INTERMEDIATE PACKS OF ONE TYPE, STYLE AND CLASS FOR A TOTAL OF 160 INSIGNIAS SHALL BE PACKED IN A SNUG FITTING INTERMEDIATE CONTAINER. . PAGE 22, PARAGRAPH 6.6.6.2 PACKING. TEN (10) INTERMEDIATE BOXES (160 EACH) SHALL BE PLACED IN A FIBERBOARD CONTAINER FOR A TOTAL OF SIXTEEN HUNDRED (1600) INSIGNIAS. . PAGE 12, ADD NEW PARAGRAPH; "3.3.8 FASTENER TAPE, HOOK. THE HOOK TAPE SHALL CONFORM TO TYPE II, CLASS 1 OF A-A-55126, OR YKK SA200(ACU) POWERHOOK OR VELCRO HTH 841 EXTRUDED HOOK, OR SIMILAR BRAND OFFERING A MINIMUM OF 1 LB PEEL/ INCH WIDTH AND 30 LB/SQUARE INCH SHEAR STRENGTH. NO SLIT OR SPLIT EDGES ARE PERMITTED. SEW ALL HOOK AND LOOP A MINIMUM OF 1/8 INCH FROM BOUND SELVAGE TO PREVENT NEEDLE CUTTING ALONG EDGES. TO PREVENT RAVELING, DO NOT SEW DIRECTLY ON SELVAGE. HOWEVER, EACH REQUIRED WIDTH SHALL MAINTAIN A TOLERANCE OF PLUS 1/32 INCH OR MINUS 1/32 INCH AS TO PREVENT STITCHING RUNOFFS OR IMPROPER FIT INTO AUTOMATIC SEWING EQUIPMENT. 3.3.8.2 - STITCHING SHALL BE CONTINUOUS. NO BROKEN, LOOSE, MISSING, INCOMPLETE STITCHING OR RUN-OFF ARE ALLOWED. IF THE STITCHING IS INTERRUPTED, BACKSTITCHING OF A MINIMUM OF 3 STITCHES SHALL BE ACCEPTABLE." . PAGE 19, TABLE IV. VISUAL EXAMINATION OF THE END ITEM. ADD NEW EXAMINATIONS AT THE END OF TABLE. EXAMINE DEFECT MAJOR / MINOR CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 8 OF 36 PAGES SPE1C1-22-T-1693 SECTION B "TAPE HOOK TAPE HAS SPLIT X . AND/OR SPLIT EDGES. STITCHES BROKEN, LOOSE OR X . MISSING. . STITCHES NOT BACK- X . STITCHED A MINIMUM . OF 3 STITCHES. . RUN-OFFS. X THREAD THREAD IS NOT A X . GOOD MATCH TO THE . INSIGNIA CLOTH." . ...................POINT OF CONTACT FOR SHADE SAMPLE AND APPROVAL IS MELANIE KING, NATICK SOLDIERS CENTER, KANSAS STREET, NATICK, SA 01760-5019, TELEPHONE 508-233-5468."\ PAGE 2, UNDER TYPE IV ADD *STYLE 6 @ ACU) PAGE 2, UNDER TYPE V ADD *STYLE 5 @ ACU) PAGE 4, UNDER TYPE IX ADD *STYLE 6 @ ACU) PAGE 4, UNDER TYPE X ADD *STYLE 5 @ ACU) PAGE 4, UNDER TYPE XI ADD *STYLE 3 @ ACU) PAGE 11, ADD THE FOLLOWING NEW INFORMATION FOLLOWING THE ABOVE INFORMATION: A.U.S. ARMY RANK INSIGNIA SHALL BE EMBROIDERED ON THE DIGITAL PIXILATED PATTERN OF THE UNIVERSAL CAMOUFLAGE PRINTED NYLON/COTTON WIND RESISTANT POPLIN CLOTH CONFORMING TO CLASS 8 OF MIL-C-44436(GL) WITH HOOK FASTENER ON THE REVERSE SIDE. B. THE LENGTH OF THE CLOTH SHALL BE CUT IN THE FILLING DIRECTION (I.E., FROM SELVAGE TO SELVAGE). A STRIP OF WASHABLE FUSIBLE INTERLINING SHALL BE CENTERED AND FUSED TO THE UNDERSIDE OF THE CUT FABRIC. THE OVERALL FINISHED SIZE FOR RANKS SHALL BE AS FOLLOWS: GENERAL AND LIEUTENANT GENERAL SHALL BE 2 INCHES WIDE AND 3-1/4 INCHES HIGH. MAJOR AND BRIGADIER GENERAL SHALL BE 2 INCHES WIDE BY 2 INCHES TALL COLONEL - PRIVATE (0-6 THROUGH E-2) SHALL BE 2 INCHES WIDE BY 2 INCHES HIGH. C. ALL GENERAL STARS SHALL BE 3/4 INCH IN DIAMETER, POINT TO VERTEX, 1/8 APART. D. ALL EMBROIDERY SHALL BE A GOOD MATCH TO BLACK CABLE HAN 67138 EXCEPT 2ND LIEUTENANT AND MAJOR SHALL BE A GOOD MATCH TO BRONZE CABLE HAW 67147 AND WARRANT OFFICERS SHALL BE A GOOD MATCH TO FOLIAGE GREEN 504 AND BLACK CABLE 67138. E.THE HOOK FASTENER SHALL COVER THE ENTIRE BACK OF THE BASE CLOTH AND SHALL BE SEWN TO THE HEMMED EDGE USING THREAD THAT IS A GOOD MATCH TO THE FOLIAGE GREEN 504 (FOLIAGE GREEN HDB 67202 OF THE DEPARTMENT OF DEFENSE STANDARD SHADE FOR HERALDIC YARNS FOR . ALL UNIVERSAL CAMOUFLAGE PATTERN CLOTH SAMPLES MUST BE APPROVED BY MELANIE KING, NATICK SOLDIERS CENTER, KANSAS STREET, NATICK, MA 01760-5019, TELEPHONE 508-233-5468." THESE DEVIATION TO THE SPEC HAVE BEEN APPROVED BY PAMELA MADIGAN OF IOH. . ADDITIONAL INTERIM CHANGES TO MIL-DTL-14651A. DEPARTMENT OF DEFENSE STANDARD SHADE FOR HERALDIC YARNS FOR EMBROIDERY AND RIBBONS). THE INSIGNIA FOR GENERAL AND LIEUTENANT GENERAL CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 9 OF 36 PAGES SPE1C1-22-T-1693 SECTION B SHALL HAVETHE SAME SIZE(2 INCH BY 3-1/4 INCH) FASTENER ATTACHED TO THE HOOK FASTENER. F.IN THE INTERIM, THE USE OF CAMOUFLAGE GREEN 483 AND BLACK CABLE 67138 UNTIL THE FOLIAGE GREEN 504 SHADE HOOK FASTENER IS AVAILABLE. G.THE HOOK FASTENER SHALL BE TYPE II, CLASS 1 OF A-A-55126. THE HOOK FASTENER SHALL BE FREE OF SLIT OR SPLIT EDGES. VELCRO BRAND HTH 841 EXTRUDED HOOK OR SIMILAR BRAND OFFERING A MINIMUM OF 1 POUND PEEL PER INCH AND 30 POUND PER SQUARE INCH SHEAR STRENGTH MAY BE USED. H.THE EMBROIDERY NEEDLE THREAD SHALL BE POLYESTER FILAMENT. THE BOBBIN THREAD SHALL BE EITHER A COTTON WARP, POLYCOTE, TYPE I, TICKET 50, 2 PLY CONFORMING TO A^A-50199 OR A 100% NYLON, TYPE I, CLASS A, 210 DENIER (7O/3PLY) CONFORMING TO V-T-295. I.THE SEWING THREAD SHALL BE FOLIAGE GREEN 504 CONFORMING TO A-A-50199 AND BE COTTON (TYPE I) OR POLYESTER COVERED POLYESTER CORE (TYPE II),COMMERCIAL SIZE TICKET NO.50 (TEX SIZE 36 TO 45) WITH A MINIMUM BREAKING STRENGTH OF 3.2 POUNDS. (TYPE I) AND 3.7 POUNDS (TYPE II) WHEN TESTED AS SPECIFIED IN ASTM D 256 AS AN ALTERNATE, TICKET NO.70(TEX SIZE 31 TO 35) WITH A BREAKING STRENGTH OF 2.6 POUNDS (TYPE I) AND 3.0 POUNDS (TYPE II), WHEN TESTED IN ACCORDANCE WITH ASTM D 2256 MAY BE USED AS THE BOBBIN OR LOOPER THREAD. ALL THREAD SHALL BE NON-STAINING AND SHOW GOOD COLORFASTNESS TO LAUNDERING. ALL CHANGES HAVE BEEN APPROVED BY IOH. . ADDITIONAL INTERIM CHANGES TO MIL-DTL-14651A. DEPARTMENT OF DEFENSE STANDARD SHADE FOR HERALDIC YARNS FOR EMBROIDERY AND RIBBONS). THE INSIGNIA FOR GENERAL AND LIEUTENANT GENERAL SHALL HAVETHE SAME SIZE(2 INCH BY 3-1/4 INCH) FASTENER ATTACHED TO THE HOOK FASTENER. F.IN THE INTERIM, THE USE OF CAMOUFLAGE GREEN 483 AND BLACK CABLE 67138 UNTIL THE FOLIAGE GREEN 504 SHADE HOOK FASTENER IS AVAILABLE. G.THE HOOK FASTENER SHALL BE TYPE II, CLASS 1 OF A-A-55126. THE HOOK FASTENER SHALL BE FREE OF SLIT OR SPLIT EDGES. VELCRO BRAND HTH 841 EXTRUDED HOOK OR SIMILAR BRAND OFFERING A MINIMUM OF 1 POUND PEEL PER INCH AND 30 POUND PER SQUARE INCH SHEAR STRENGTH MAY BE USED. H.THE EMBROIDERY NEEDLE THREAD SHALL BE POLYESTER FILAMENT. THE BOBBIN THREAD SHALL BE EITHER A COTTON WARP, POLYCOTE, TYPE I, TICKET 50, 2 PLY CONFORMING TO A^A-50199 OR A 100% NYLON, TYPE I, CLASS A, 210 DENIER (7O/3PLY) CONFORMING TO V-T-295. I.THE SEWING THREAD SHALL BE FOLIAGE GREEN 504 CONFORMING TO A-A-50199 AND BE COTTON (TYPE I) OR POLYESTER COVERED POLYESTER CORE (TYPE II),COMMERCIAL SIZE TICKET NO.50 (TEX SIZE 36 TO 45) WITH A MINIMUM BREAKING STRENGTH OF 3.2 POUNDS. (TYPE I) AND 3.7 POUNDS CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 10 OF 36 PAGES SPE1C1-22-T-1693 SECTION B (TYPE II) WHEN TESTED AS SPECIFIED IN ASTM D 256 AS AN ALTERNATE, TICKET NO.70(TEX SIZE 31 TO 35) WITH A BREAKING STRENGTH OF 2.6 POUNDS (TYPE I) AND 3.0 POUNDS (TYPE II), WHEN TESTED IN ACCORDANCE WITH ASTM D 2256 MAY BE USED AS THE BOBBIN OR LOOPER THREAD. ALL THREAD SHALL BE NON-STAINING AND SHOW GOOD COLORFASTNESS TO LAUNDERING. ALL CHANGES HAVE BEEN APPROVED BY IOH. . DEVIATION FROM DPSCM 4155.3: PAGE 1, PARA. 1 - AFTER PARA. 1D ADD NEW PARA. 1E: "1E. USE OF ONE OR MORE END ITEM TEST REPORTS FOR COMBINING INSIGNIA ITEMS IN TESTING IS AUTHORIZED PROVIDED CERTIFICATION OF TEST REPORTS STATES THAT THE SAME YARN WAS EMPLOYED IN THE EMBROIDERY OF ALL DESIGNS IN THE LOT AND FURTHER THAT THE QUANTITY (LBS) OF YARN INVOLVED IN EMBROIDERING THE END ITEM IS INDICATED IN THE REPORT. THE QUALITY ASSURANCE REPRESENTATIVE IS AUTHORIZED TO COMBINE SAMPLES OF INSIGNIA FOR SUBMITTAL ON DD FORM 1222 TO THE DLA TROOP SUPPORT LABORATORY FOR VERIFICATION TESTING." ADDITIONAL INFORMATION FOR V-T-276: V-T-276 HAS BEEN CANCELLED AND REPLACED BY A-A-52094 A-A-52094B Thread, Cotton dated 01 May 2019 No Additional Information (ref. T1481) ADDITIONAL INFO FOR UU-P-268: UU-P-268 IS CANCELLED. USE A-A-203C DATED 1/3/96 AND A-A-1894A DATED 5/27/93. (ref. T0688 - 9/11/06) ADDITIONAL INFORMATION FOR CCC-C-461: . INTERIM CHANGES TO CCC-C-461C, AM. 1: . PAGE 1, PARA 2.1, ADD THE FOLLOWING NEW TYPE TO THE TABLE: . TYPE NOMINAL WEIGHT YARN PLY YARN . OZ. PER SQ. YD. WARP-FILLING "TYPE VII" "7.6" "1X1" "COMBED" . PAGE 3, ADD NEW PARAGRAPH: "2.1.1 NON-GOVERNMENT PUBLICATIONS. THE FOLLOW- ING DOCUMENTS FORM A PART OF THIS DOCUMENT TO THE EXTENT SPECIFIED HEREIN. UNLESS OTHERWISE SPECIFIED, THE ISSUES OF THE DOCUMENTS WHICH ARE DOD ADOPTED ARE THOSE LISTED IN THE ISSUE OF THE DODISS CITED IN THE SOLICITATION. UNLESS OTHERWISE SPECIFIED, THE ISSUES OF DOC- UMENTS NOT LISTED IN THE DODISS ARE THE ISSUES OF THE DOCUMENTS CITED IN THE SOLICITATION (SEE 6.2) . AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS . AATCC-8 COLORFASTNESS TO CROCKING: AATCC . CROCKMETER METHOD AATCC-15 COLORFASTNESS TO PERSPIRATION AATCC-16 COLORFASTNESS TO LIGHT AATCC-20 FIBER ANALYSIS: QUALITATIVE AATCC-20A FIBER ANALYSIS: QUANTITATIVE AATCC-61 COLORFASTNESS TO LAUNDERING, HOME . AND COMMERCIAL: ACCELERATED AATCC-81 PH OF THE WATER-EXTRACT FROM CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: CONTINUED ON NEXT PAGE PAGE 11 OF 36 PAGES SPE1C1-22-T-1693 SECTION B . BLEACHED TEXTILES AATCC-96 DIMENSIONAL CHANGES IN COMMERCIAL . LAUNDERING OF WOVEN AND KNITTED . FABRIC EXCEPT WOOL (COPIES OF THESE DOCUMENTS ARE AVAILABLE ONLINE AT HTTP://WWW.AATCC.ORG OR FROM THE AATCC NATIONAL HEADQUARTERS, P.O. BOX 12215, RESEARCH TRIANGLE PARK, NC 27709-2215.) . ASTM INTERNATIONAL . ASTM-D-276 IDENTIFICATION OF FIBERS IN . TEXTILES ASTM-D-629 QUANTITATIVE ANALYSIS OF TEXTILES ASTM-D-1683 FAILURE IN SEWN SEAMS OF WOVEN . FABRICS ASTM-D-2165 PH OF AQUEOUS EXTRACTS OF WOOL AND . SIMILAR ANIMAL FIBERS ASTM-D-3775 FABRIC COUNT OF WOVEN FABRIC ASTM-D-3776 MASS PER UNIT AREA (WEIGHT) OF . FABRIC ASTM-D-5034 BREAKING FORCE AND ELONGATION OF . TEXTILE FABRICS (GRAB METHOD) (COPIES OF THESE DOCUMENTS ARE AVAILABLE ONLINE AT HTTP://WWW.ASTM.ORG OR AT ASTM INTERNATIONAL, 100 BARR HARBOR DRIVE, WEST CONSHOHOCKEN, PA 19428-2959.)" . PAGE 4, TABLE I, AT END OF TABLE ADD: TYPE-"VII", YARN-"COMBED", YARN PLY WARP FILL- "1" "1", WEIGHT OZ. PER SQ. YD (MIN)(MAX)- "7.2" "8.0", YARNS PER INCH (MINIMUM) WARP FILL - "100" "54", BREAKING STRENGTH POUNDS (MINIMUM) WARP FILL-"120" "90", WEAVE-"3/1 TWILL TO LEFT" . PAGE 5, PARA 3.3.2, LINE 7, DELETE "FAIR" AND SUBSTITUTE "NOT LESS THAN "3" WHEN QUANTIFIED USING AATCC GRAY SCAL FOR COLOR CHANGE AND." PARA 3.3.4.1, LINE 5, DELETE "GOOD" AND SUBSTI- TUTE "NOT LESS THAN "3.5" WHEN QUANTIFIED USING AATCC GRAY SCALE FOR COLOR CHANGE". LINE 6, DELETE "AND NO MORE CROCKING THAN MUNSELL VALUE 8.5" AND SUBSTITUTE "AND CROCKING". . PAGE 6, PARA 3.7, LINES 2-3, AFTER "FILLING DIRECTION OF THE CLOTH, ADD: "FOR TYPES I-VI AND NO MORE THAN 3 PERCENT IN THE WARP AND 3 PERCENT IN THE FILLING FOR TYPE VII,". JUSTIFICATION: A NEW TYPE IS NEEDED FOR USE IN THE CONSTRUCTION OF MIL-H-81735. . PAGES 9, 10 AND 11, PARA 4.4, LINE 1, DELETE, "IN FED. STD. NO. 191, WHEREVER APPLICABLE, AND AS LISTED". TABLE II, MAKE THE FOLLOWING CHANGES: . FOR COTTON IDENTIFICATION, UNDER TEST METHOD, DELETE "1200", AND SUBSTITUTE "AATCC-20 OR ASTM-D-276". . FOR COMBED COTTON, DELETE "(TYPES I, II, III AND IV)" AND SUBSTITUTE "(TYPES I, II, III, IV AND VII)". . FOR DISCOLORATION (BLEACHED), UNDER TEST METHOD, DELETE "5660", AND SUBSTITUTE "AATCC- 16 OPT A". . FOR COLORFASTNESS TO LAUNDERING (AFTER 3 CYCLES), UNDER TEST METHOD, DELETE "5610", AND SUBSTITUTE "AATCC-61 TEST 3A". . FOR COLORFASTNESS TO PERSPIRATION, UNDER TEST